USA Measurements US-4011 User And Technical Manual Download

Page: 33 / 42

US-4011

Please note:

baud rate is selected by

USER-COM1

2-BAUDRT

8N1

byte format is fixed,

Hex data (0x00 – 0xff)

are used.

7.8.2.

Press down

HOLD/SETUP

key until

CONFIG

is shown, using

keys to select

TEST-COM1.RD

TEST-COM2.RD

item, press

TARE/PRESET

to enter test COM1/2 receiving function, and

rd1

.--

rd2

.--

will be

displayed first.

7.8.3.

In this mode, received hex data (0x00 – 0xff) will be displayed on -- position.

7.8.4.

Press

HOLD/SETUP

key to return to last menu item, press

ZERO/ON/OFF

key to prepare to exit this mode

7.9.

Serial Port1/2(COM1/2) Transmitting Test

7.9.1.

Before test the transmitting function of

COM1

COM2

, a cable is need to connect a PC and this instrument ,

and a software be similar with Super Terminal of Windows is also need to run on PC to receive bytes from this
instrument. Please note:

baud rate is selected by

USER-COM1/2-BAUDRT

8N1 byte format is fixed

, Hex data

(0x00 – 0xff) are used.

7.9.2.

Press down

HOLD/SETUP

key until

CONFIG

is shown, using

keys to select

TEST-COM1.TD

TEST-COM2.TD

item, press

TARE/PRESET

to enter test COM1/2 transmitting function, and

td1

.--

td2

.--

will be

displayed first.

7.9.3.

In this mode, transmitted hex data (0x00 – 0xff) will be displayed on -- position, and

keys can

be used to modify transmitted data.

7.9.4.

Press

HOLD/SETUP

key to return to last menu item, press

ZERO/ON/OFF

key to prepare to exit this mode.

Summary of Contents for US-4011











































Search results

Summary of Contents for US-4011

Reviews:

Related manuals for US-4011

Brands by name

Popular brands

USA Measurements US-4011, User And Technical Manual

Search results

Summary of Contents for US-4011

Reviews:

Related manuals for US-4011

Brands by name

Popular brands