1
z
LCD, POSITIVE REFLECTIVE OR NEGATIVE TRANSMISSIVE
WITH YELLOW/GREEN OR RED BACKLIGHTING
z
0.6 INCH (15.2 mm) HIGH DIGITS
z
ADJUSTABLE TIMEBASE FROM 4 MSEC TO 32 SEC
z
INTERNAL LITHIUM BATTERY PROVIDES OVER 7 YEARS OF
CONTINUOUS OPERATION
z
NEMA 4X/IP65 SEALED FRONT PANEL BEZEL
z
ACCEPTS MAGNETIC OR LOGIC TYPE SIGNAL INPUTS
z
WIRE CONNECTIONS MADE VIA SCREW CLAMP
TYPE TERMINALS
DESCRIPTION
The Ditak 8 is a self-powered rate indicator which features selectable
Timebase Increments by setting the appropriate DIP switches on the rear of the
unit. The internal 3.0 VDC lithium battery will operate continuously for at least
7 years. It has a 5-digit LCD display with 0.6 inch (15.2 mm) high digits. The
displays are available in positive image reflective (black digits, reflective
background) or negative image transmissive (illuminated digits, dark
background) with red or yellow/green backlighting. Backlight version units
require power from an external 9 to 28 VDC supply.
The unit is constructed of a lightweight, high impact plastic case with a clear
viewing window. The sealed front panel meets NEMA 4X/IP65 specifications
for wash-down and/or dusty environments, when properly installed.
The optional Micro Line/Sensor Power Supply (MLPS1000) is designed to
attach to the rear of an installed Ditak 8. The optional supply can be powered
from 85 to 250 VAC, and can provide power for the backlighting of a unit and
most sensors.
SAFETY SUMMARY
All safety related regulations, local codes and instructions that appear in the
manual or on equipment must be observed to ensure personal safety and to
prevent damage to either the instrument or equipment connected to it. If
equipment is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.
SPECIFICATIONS
1.
DISPLAY:
5-Digit LCD, 0.6" (15.2 mm) high digits.
2.
POWER SOURCE:
Internal 3.0 V lithium battery provides over 7 years of
continuous service (battery life is dependent upon usage).
3.
BACKLIGHT POWER REQUIREMENTS:
9 to 28 VDC @ 35 mA.
Above 26 VDC, derate operating temperature to 50°C. Must use the MLPS1
or a Class 2 or SELV rated power supply.
4.
SIGNAL INPUT:
0 to 10 KHz from a magnetic or bi-polar output (with a
50% duty cycle). Min. input sensitivity is 0.9 V. Max. input = 28 VDC.
5.
TIMEBASE:
Adjustable in 1/256 sec (3.906 msec) increments via DIP
switches located at the rear of the unit. Timebase ranges from 3.906 msec to
31.998 sec; 0.01% ±1 digit accuracy.
6.
ENVIRONMENTAL CONDITIONS:
Operating Temperature
: 0 to 60°C (Above 50°C derate backlight operating
voltage to 26 VDC max.)
Storage Temperature
: -40 to 80°C
Operating and Storage Humidity
: 85% max. (non-condensing) from 0°C to
60°C.
Altitude
: Up to 2000 meters
7.
CONSTRUCTION:
High impact plastic case with clear viewing window
(Panel gasket and mounting clip included). Installation Category I, Pollution
Degree 2.
DITAK 8 - ADJUSTABLE TIMEBASE 5-DIGIT RATE INDICATOR
DIMENSIONS In inches (mm)
Note: Recommended minimum clearance (behind the panel) for
mounting clip installation is 2.15" (54.6) H x 3.00" (76.2) W.
CAUTION: Risk of Danger.
Read complete instructions prior to
installation and operation of the unit.
Bulletin No. DT8-B
Drawing No. LP0555
Released 8/06
MODEL NO.
DESCRIPTION
PART NUMBER
DT8
Adjustable Timebase Tachometer
DT800000
DT800010
DT800020
MLPS
Micro Line Sensor/Power Supply
MLPS1000
Adjustable Timebase Tachometer with
Yellow/Green Backlighting
Adjustable Timebase Tachometer with
Red Backlighting
For more information on Pricing, Enclosures & Panel Mount Kits refer to the RLC
Catalog or contact your local RLC distributor.
ORDERING INFORMATION