background image

USB 9640 5-Channel LED PAR 

     

 

 

     

 

 

     

 

© US Blaster Europe BV   

Connection of DMX 

Connect the provided DMX XLR cable to the female 3-pin XLR output of your controller and the 
other side to the male 3-pin XLR input of the fixture (please refer to the figure “

Installation  and 

Operation

” below). 

You must chain multiple fixtures together through serial linking, never split your DMX connections 
unless you are using a splitter/signal amplifier. 

 

 

 
DMX addressing 

All fixtures should be given a DMX starting address when using a DMX controller, so the correct 
fixture responds to the correct control signal. This digital starting address is the channel number 
from  which  the  fixture  starts  to  "listen"  to  the  digital  control  information  sent  out  from  the  DMX 
controller.  The  allocation  of  this  starting  DMX  address  is  achieved  by  various  combining  the 
dipswitches. 

 

This fixture employs 10 dipswitches to access its functions. Normally the dipswitches from #1 to 
#9 are used for encoding DMX address, the dipswitch #10 for enabling DMX mode. 

 

Dipswitch 1 address equals to 1 
Dipswitch 2 address equals to 2 
Dipswitch 3 address equals to 4 
Dipswitch 4 address equals to 8 
Dipswitch 5 address equals to 16   
Dipswitch 6 address equals to 32 
Dipswitch 7 address equals to 64 
Dipswitch 8 address equals to 128 
Dipswitch 9 address equals to 256 
DMX address=Dipswitch 1+Dipswitch 2+…+Dipswitch 9. 

Summary of Contents for USB 9640













Reviews: