Urrea SS950 User Manual And Warranty Download Page 12

12

BLADE SELECTION
In order to obtain the best performance from 
the saw, it is important to select the correct 
blade for the particular application and type 
of material to be cut.

BASE (SHOE) ASSEMBLY
Sliding the Shoe in or 
out
For maximum control 
and longer blade life, 
the base assembly 
slides in or out in or-
der to adjust the ef-
fective stroke length.
1. Disconnect the saw from the power supply.
2. Press the shoe-release button, and slide the 
shoe to the desired position. The shoe can be 
locked in any position.
3. Release the shoe-release button in order to 
lock the shoe in the desired position.

Pivoting the shoe The 
shoe pivots in order 
to provide maximum 
control against the 
surface being cut.
1. Disconnect the saw 
from the power sup-
ply.
2. Hold the saw securely, and then pivot the 
shoe to the desired angle.

SCROLLING/ORBITAL/STRAIGHT FUNCTION
1. Disconnect the saw 
from the power sup-
ply.
2. Turn the indicator 
to the “

” position 

in order to allow the 
saw head to be ro-
tated relative to the 
body.
3. Move the knob to either cutting action set-
ting in order to lock the saw head in position.
4. Turn the knob to the “

” position for 

straight cutting action.
5. Turn the knob to the “

” position for or-

bital cutting action. 
This reciprocating saw has pendulum action 
in order to make the blade swing slightly as it 
cuts. Pendulum action increases the speed of 

cut, but may result in a rougher finish to the 
cut in some materials.
Experiment on a piece of scrap material in or-
der to determine the optimum pendulum ac-
tion setting.

GENERAL CUTTING
1. Hold the saw firmly so that it is positioned in 
front of and away from the operator.
2. Make sure the saw blade is clear of any for-
eign material.
3. Make sure the material to be cut is securely 
supported. Small workpieces must be securely 
clamped in a vise or clamped to a workbench 
or table.
4. Clearly mark the cutting line.
5. Depress the trigger switch in order to start 
the cutting action.
6. Place the base assembly (shoe) against the 
work, and then move the blade into the work-
piece.
7. Do not force. Use only enough pressure to 
keep the saw cutting. Let the blade and the 
saw do the work. The use of excessive pressure 
may cause bending or twisting of the blade, 
which may result in broken blades.

PLUNGE CUTTING
1. Clearly mark the cutting line.
2. Choose a convenient starting point inside 
the area to be cut out, and place the tip of the 
blade above that point.
3. Rest the front edge of base assembly (shoe) 
on the workpiece, and hold it firmly in posi-
tion.
4. Depress the trigger switch in order to start 
the cutting action.
5. When the saw blade reaches full cutting 
speed, slowly tilt saw downward until the tip 
of the blade starts cutting the workpiece.
6. After the blade penetrates the workpiece, 
tilt the saw until the blade is perpendicular to 
the workpiece.

METAL CUTTING
The saw can be used to cut metals, such as 
sheet steel, pipe, steel rods, aluminium, brass, 
and copper. Be careful not to twist or bend the 
saw blade. Do not force.
The use of cutting oil is recommended when 
cutting soft metals and steel.

SS950 manual.indd   12

07/09/16   9:35 a.m.

Summary of Contents for SS950

















Reviews: