Urrea SI910 User Manual And Warranty Download Page 16

16

Before connecting the tool to a power source 
(receptacle, outlet, etc.) be sure that the volt-
age supplied is the same as that one specified 
on the nameplate of the tool.
 To use a not 
specified voltage may cause a serious injury to 
the user as well as damage the tool.

 IMPORTANT: This appliance is not intended 

for use by persons (including children) with re-
duced physical, sensory or mental capabilities 
may be different or reduced, or lack of experi-
ence or knowledge, unless such persons are su-
pervised or trained to operate the product by 
a person responsible for their safety. Children 
should be supervised to ensure they do not use 
the devices as toys.

TOOL USE AND CARE

Do not force the power tool. Use the correct 
tool for the application.
 The correct tool will 
do the job better and more safely at the rate 
that it was designed to work at.
Do not use tools if switch does not turn it on 
or off.
 Any tool that cannot be controlled with 
the switch is dangerous and must be repaired.
Disconnect the plug from the power source 
before making any adjustments, changing ac-
cessories or storing the tool.
 This preventive 
safety measures reduce the risk of accidental 
starting of the tool.
When the power tool is not in use, store it out 
of the reach of children, and do not allow in-
dividuals who are not familiar with the power 
tool or these instructions to operate it.
 Power 
tools are dangerous in the hands on untrained 
users.
Maintain the power tool. Check for misalign-
ment or binding of moving parts, broken parts, 
and any other condition that may affect the 
operation of the power tool. 
If it is damaged, 
have it repaired before using. Many accidents 
are caused by poorly maintained power tools.
Check for misalignment or bonding of moving 
parts, breakage parts, and any other condition 
that may affect the tools operation.
 If you find 
a damaged tool, take it to service before use it. 
Use only accessories that are recommended by 
the manufacturer of your model.
 Suitable ac-
cessories for one tool, may become hazardous 
when are used on another tool.

Keep cutting tools, sharpened and clean. Cut-
ting tools in good condition with sharpened 
edges, are less likely to stuck in workpieces or 
easier to control.
Is recommendable to use a safety device suit-
able, such a thermal and differential switch 
when you are using an electric equipment.

SERVICE

Tool service must be performed only by quali-
fied repair personnel. Service or maintenance 
performed by unqualified personnel could re-
sult in a risk of injury.

SPECIFIC SAFETY RULES FOR 

COMPOUND MITER SAW

• Wear eye protection.
• Keep hands out of path of saw blade. Avoid 
contact with any coasting blade. It can still 
cause severe injury.
• Do not operate saw without guards in place. 
Check blade guard for proper closing before 
each use. Do not operate saw if blade guard 
does not move freely and close instantly. Never 
clamp or tie the blade guard in the open posi-
tion.
• Do not perform any operation freehand. The 
workpiece must be secured firmly against the 
rotary table and guide fence with the vise dur-
ing all operations. Never use your hand to se-
cure the workpiece.
• Never reach around the saw blade.
• Turn off tool and wait for saw blade to stop 
before moving workpiece or changing set-
tings.
• Unplug tool before changing blade or servic-
ing.
•Always secure all moving parts before carry-
ing the tool.
• Stopper pin which locks the cutter head 
down is for carrying and storage purposes only 
and not for any cutting operations.
• Do not use the tool in the presence of flam-
mable liquids or gases.
• Check the blade carefully for cracks or dam-
age before operation. Replace cracked or dam-
aged blades immediately.
• Use only the type of clamp recommended for 
this tool.

SI910 manual.indd   16

09/06/16   12:28 p.m.

Summary of Contents for SI910





























Reviews: