sec.2b
−−−−
3
K-STEEL CALL MODULE
BIBUS 2
nd
Ed. VOP - Technical Manual
Ref.
072/
4
K-STEEL CALLING MODULE WITH REPERT
ORY
To restore default settings:
Disconnect module power.
Hold the red programming button pressed and power up the
module.
Hold the button pressed for approximately 10 seconds and wait
for a tone.
Release the button.
OPERATION
CALLS TO USERS
A user can be called by entering the user’s code on the keypad.
Obviously, the code must be known to do so. The name can be sought
in the integrated electronic directory if the code is not known.
CALLS TO USERS BY SELECTING THE NAME
The following message will appear on the display:
Press or to scroll the names and the codes. Hold either button
pressed to increase scrolling speed.
Select the name and press
to call the selected user.
The apartment door phone will ring for approximately 3 seconds. Hold
pressed to send up to three consecutive calls.
Name/code display example:
The following prompt will appear on the display if
is not pressed for
longer than two seconds after selecting a name:
At this point, press
to call or press or to scroll the name list.
The following will appear on the display when the button
is
pressed:
Press to interrupt the call to the previously selected user.
The following message will appear on the display if the user picks up
the handset:
Press to end the conversation with the user.
The following message will appear if the user does not answer within
the programmed pick-up time:
•
•
•
•
DESCRIPTION
OF
TERMINALS
AND
CONNECTORS
MP terminal board
~0
Power 12Vac
~12
Power 12Vac
+T
Back-up power positive
GND
Back-up power negative
SE1
Electrical lock connection
SE2
Electrical lock connection
MP2 terminal board
L1
Bus line 1st wire
L2
Bus line 2nd wire
GND
Reference electrical ground
PA
Hall door opener button input
SP
Open door sensor contact input
Mv terminal board
SN
Video power unit on signal for video door phone systems
R
Video switching enable signal for video door phone
systems
R1
Video power ground
MS terminal board
H
Door opener code time band contact input
P
Mail key input
GND
Reference electrical ground
+EP
Auxiliary device power
DT
Not used
CNA
Alphabetic keyboard connector 1038/73
CNP
Programming keyboard connector 1032/65
CNS
PC serial line connector
The module is programmed by default with a jumper between ground
and the “SP” signal to simulate the door closed contact. Remove the
jumper and connect the sensor between GND and SP when the open
door contact is required.
Connect the electrical lock positive to terminal SE1 and the negative
to terminal SE2 when polarised electrical locks are used.
IMPORTANT: Observe the instructions contained in section for
wiring and maximum distances.
TECHNICAL SPECIFICATIONS
Power:
2vac rated
Stand-by consumption:
300mAac max.
Maximum consumption:
600mAac max. (*)
R signal:
Imax=80mA
Lock hold current:
90mA max.
Working temperature range:
-0 +50°C
Humidity:
90% RH at 30°C
(*) With alphabetic keyboard 1038/73.
DEFAULT SETTINGS
Refer to section 1A “Programming” in this manual for how to
program the device.
The default settings of the device are:
System type:
2nd Edition
Station type:
main
Code format:
numeric (000–9999)
Station number:
Pick-up time:
20s
Busy time:
20s
Door opener time:
pulse
§
•
•
•
•
•
•
•
K-STEEL CALLING MODULE WITH REPERTORY Ref. 072/4
DESCRIPTION OF TERMINALS AND CONNECTORS - TECHNICAL SPECIFICATIONS
DEFAULT SETTINGS - OPERATION
Select NAME
with
↑
or
↓
To call
press
URMET
1001
CALL
IN COURSE
TALK
PLEASE
User
does not reply
