urmet domus 5454475, Manual

Page: 9 / 24

WARRANTY: In addition to the warranty required by law, this product is guaranteed for 5 years from date of manufacture. The material must be used accor-
ding to the instructions provided and for its intended use. Faults must not be caused by deterioration or accidents resulting from negligence, anomalous use
or incorrect installation. In all cases, the warranty only includes replacement of faulty products. No compensation for loss or damage may be claimed.
DS1054-207B P2 P9
Urmet S.p.a. – 10154 TOrINO (ITaLY) – Via Bologna 188/C
For technical information, go to www.yokis.com or call:
Customer Service: +39 011.23.39.810 –
export dept. Phone: +39 011.24.00.250/256 – Fax: +39 011.24.00.296
TRANSMITTER SETTINGS
Opening (can be used in all modes) : Press the transmitter 10 times , and press 3 times when the LED starts
blinking.
Timed opening (can be used in Yokis Master or Universal mode) . Press the transmitter 10 times , and press
16 times when the LED starts blinking. Do not forget to set the timed delay (make 23 short presses to unlock
the module, X short presses according to table and 25 short presses to set duration in seconds, if necessary) .
Partial opening (can be used in Faac Master mode only for pedestrian entrance) : Press the transmitter 10
times , and press 2 times when the LED starts blinking.
Others.
Closing : Press the transmitter 10 times , and press 4 times when the LED starts blinking.
Open / Stop / Close / (Stop) : Press the transmitter 10 times , and press once when the LED starts blinking.
COMPATIBILITY WITH YOKIS PRO AND YNO APPS
The radio automation actuators MAU500ERP are perfectly integrated in the YOKIS PRO app. This means that
you can position, set the parameters and centralise the device directly on your tablet equipped with YOKEY
radio USB dongle (Ref. 5454491) and YOKIS PRO app.
By adding a YOKISHUB (Ref. 5454495) your customers can control the automated devices in wireless mode
(changing mode, timing use etc.) and integrate it in scenarios directly on their YOKIS YnO habitat control app.
MAU500ERP modules can be directly controlled by the end user YOKIS YnO App in order to drive gates, garage
door openers, etc…
dIreCTIVe 2012/19/eU OF THe eUrOPeaN ParLIaMeNT aNd OF THe COUNCIL of 4 July
2012 on waste electrical and electronic equipment (Weee)
The symbol of the crossed-out wheeled bin on the product or on its packaging indicates that this product must
not be disposed of with your other household waste.
Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection
point for the recycling of waste electrical and electronic equipment.
The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natu-
ral resources and ensure that it is recycled in a manner that protects human health and the environment.
For more information about where you can drop off your waste equipment for recycling, please contact your local
city office, your household waste disposal service or the shop where you purchased the product.
1 - Establish a radio connection between the receivers by pressing the "connect" button of the first receiver
once (the LED of the receiver will start blinking), then press the "connect" button of the second receiver
once . Both receivers will blink once to confirm the connection.
2 - Connect the transmitter to the receiver to be controlled by pressing the chosen pushbutton on the transmitter
(E) 5 times . Press the pushbutton in the “Connect” hole of the receiver (R) while the transmitter LED is flas-
hing. The receivers will make the relay blink briefly and the LED of the transmitter will stop blinking.
3 - At this point, create an access point on the receiver nearest to the transmitter by pressing the transmitter (E)
pushbutton 7 times (the same one programmed in the previous step). The transmitter LED will start flashing
rapidly. Then press the pushbutton in the “Connect” hole of the first receiver (R) once ( 1 press ). The trans-
mitter and receiver LED will stop flashing.
HOW TO INCREASE THE RANGE USING AN INTERMEDIATE RECEIVER