Use only the cable supplied and a CE-certified mains charger with the following output parameters: 5V and 0.3 - 2 A (printed on the charger).
Do not use fast chargers.
OFF
Bip Bip Bip
Bip Bip Bip
0 - 15
ON
Bip
Bip
ADHESIVE GEL REFILL PREPARATION
Open the bag and take a refill of adhesive gel. One refill corresponds to the right part of
the patch and the other to the left part. Remove carefully the blue protective film,
making
sure that the adhesive gel remains firmly in place on the transparent protective
film.
If necessary, you can retain the gel with your finger. Keep the blue protective film you will
need it to put it back on the patch after each use.
2
APPLYING GELS ON THE PATCH
Using the transparent protective film, place one of the gels on the patch correctly;
making sure that
the tab of the gel is perfectly overlaid with the one of the patch.
Do
the same with the 2
nd
gel by following again the steps 2 & 3.
Once the two gels are positioned on the electrical circuits, remove the 2 transparent
protective films making sure that the gel remains on the patch (if necessary, you can
retain the gel with your fingers).
1 pair of adhesive gels = about 30 uses.
(Comment : you can throw away the transparent protective film.)
3
6
PATCH STORAGE
Before removing the patch, make sure it is switched off. Then
carefully
remove the
patch, making sure that the gels remain on the electrical circuit (if necessary, you can
retain the gel with your fingers).
Leave the adhesive gels on the patch and cover them
with the preserved blue protective film.
Your patch is ready for the next use. Store the
patch in the transportation box provided.
For the next uses, remove the blue protective film and refer directly to step 4.
PATCH STORAGE
Before removing the patch, make sure it is switched off. Then
carefully
remove the
patch, making sure that the gels remain on the electrical circuit (if necessary, you can
retain the gel with your fingers).
Leave the adhesive gels on the patch and cover them
with the preserved blue protective film.
Your patch is ready for the next use. Store the
patch in the transportation box provided.
For the next uses, remove the blue protective film and refer directly to step 4.
PATCH APPLICATION AND INITIATION
Apply the patch on the painful area, as shown in the illustration, and briefly press the
button . 1 sound signal is heard and a green light lights up.
This is PROGRAM 1.
If you do not see a green light or hear a beep, it means that the patch is completely
discharged. Recharge the patch using the supplied cable.
4
COMMENT:
When the patch does not stick enough to the skin anymore,
it is necessary to moisten the
gels in order to extend their lifetime, as it is advised in the manual.
7
Bip Bip
Bip Bip
PROGRAM SELECTION
3 programs
are available.
Each program lasts 30 minutes.
For more details please
refer to the manual. When you turn on the patch
PROGRAM 1 is selected by default
: this
program is recommended for 1
st
use.
To change the program, press the button for
a long time
(approx. 3 seconds, until you hear a series of beeps): 2 beeps indicate that
program 2 is activated. Release the button.
A further prolonged press
will switch to
program 3: 3 beeps.
To start the stimulation, go to the next step.
5
STARTING STIMULATION AND ADJUSTING THE INTENSITY
Once you have selected your program, press only once and briefly on the button
to start stimulation.
Adjust the intensity by briefly pressing on the and buttons.
If the feeling is uncomfortable or painful, decrease the intensity.
15 intensity levels are available.
SWITCHING OFF THE PATCH
At the end of the 30 minutes, the patch shuts down automatically.
If you want to switch off before the end of the session of 30 minutes, press
briefly
on the
button . 3 sound signals and 3 green light signals indicate that the patch is switched
off.
IDENTIFICATION OF THE PATCH FACES
On a table, place the back side of the patch in front of you (control box against the table).
1
✓
front side
back side
See the patch’s setting up on the website:
urgo.com or via the QR code
pains
QUICK START GUIDE BEFORE FIRST USE
URGO ELECTROTHERAPY PAINFUL PERIODS RECHARGEABLE PATCH
Read this manual carefully and comply with the instructions given in it. Read warnings and contraindications carefully.
It is recommended to fully charge the patch before first use.
8
11
