background image

 

24 

5 Operation (LCD model)                                                                 

 

 

4. LED indicators 

The LED indicators contains, Bypass indicator, utility power indicator, Inverter 

indicator,  Battery  indicator.  The  definition  of  each  indicator  is  the  same  as 

LED panel (refer to table 4-1).   

 
 

5.2

 

Operation Mode 

 

UPS Operation Mode contains  normal  mode, battery  mode and bypass  mode. 

Under the three modes, the page showing output voltage and output frequency 

is the main display page. If users need more information about UPS, Pressing 

the function button can initiate display screen switch. If the current page is not 

the  main  page,  UPS  will  automatically  switch  back  the  main  page  after  30 

seconds. In order to extend the LCD usage life, the backlight will turn off after 

1 minute without any switch operation. At this point, Users just need to touch 

any button briefly to turn on the backlight. 

 

5.2.1

 

Normal mode 

When  operating  in  the  normal  mode,  the  display  of  main  page  on  the  front 

panel is shown as the figure 5-2. The  utility  power indicator and the  Inverter 

indicator  are  turned  on.  Load  information  area  shows  load  value,  and  the 

battery level area indicates  dynamically when the battery is  not  fully  charged 

(the  battery  level  icons  lit  one  after  another  circularly).  When  the  battery  is 

fully charged, all the level icons are turned on. 

 

1) If the utility power indicator blinks, it indicates that there are problems with 

reversed polarity (L, N) of site wiring or disconnect with ground. UPS is still 

working  in  normal  mode.  If  the  battery  indicator  is  turned  on  at  the  same 

time, it shows that the voltage or frequency of the utility power is out of the 

normal input range of the UPS. The UPS works in battery mode. 

 

 

Summary of Contents for Q1K









































Reviews: