background image

14

15

 UPPAbaby MESA Instruction Book

 UPPAbaby MESA Instruction Book

CHOOSING A VEHICLE SEATING LOCATION

VEHICLE C

OMP

ATIBILITY

PLEASE READ THE FOLLOWING INFORMATION  

BEFORE INSTALLING THIS CHILD RESTRAINT!

 

Always park on a level surface when installing a 
child restraint. 

 
The safest seating position is one that works  
best for your specific car seat, family and vehicle. 
When determining whether the MESA Rear-Facing 
Car Seat can be used with lower anchors in the 
rear center seating position, it is critical that you  
refer to your vehicle owner's instruction book. If 
the MESA does not install best in the rear center 
seating location, it is recommended to move to 
one of the outboard seating positions. 

Before installing this child restraint 
you must determine the method 
of installation and the best vehicle 
seating position for that method. 
This child restraint can be installed 
either using 

LATCH

 or the  

Vehicle Seat Belt

.

LOWER 

ANCHORS

VEHICLE  

SEAT BELT 

RETRACTOR

VEHICLE 

SEAT BELT

VEHICLE C

OMP

ATIBILITY

DETERMINING BEST INSTALLATION METHOD

BASE INSTALLATION

CARRIER INSTALLATION WITHOUT BASE

At this point take out your VEHICLE OWNER'S INSTRUCTION BOOK.  
You will need this to look up different features in your vehicle that might 
affect the installation. 

WARNING!

 

NEVER 

place a rear-facing only child restraint in front 

of an active airbag.

Lap/Shoulder Belt 
Installation (pg. 22)

Lower Anchor  

Installation (pg. 19)

Lap/Shoulder Belt 

Standard 

Routing Method 

(pg. 26)

Lap Belt Only 

Routing Method 

(pg. 26)

Lap Belt Only 

Installation (pg. 22)

NOTE: 

The carry  

handle must be locked  

in any (3) positions  

when in use (p. 29).

0225_MESA_INS_V4.indd   14-15

3/19/15   11:07 AM

Summary of Contents for mesa




























Reviews: