UPPAbaby mesa Manual Download Page 25

Page: 25 / 27

UPPAbaby MESA Instruction Book

STEP 1:

Insert lower part of SIP

carriage into pocket on the back
of SIP padding.

STEP 2:

Guide harness straps back

into slots in SIP padding.

STEP 3:

Secure SIP cover tightly

around SIP ears.

SIP PADDING INSTALLATION

CLEANING

CLEANING FABRICS

Fabrics include: seat pad, infant inserts, buckle pads and shoulder pad.

30C

Machine wash in cold
water on gentle cycle
with mild detergent.

Dry flat and away
from direct sunlight
before re-use or
storage.

DO NOT

bleach, iron

or dry clean.

CLEANING HARNESS W CANOPY

Spot clean using
warm water with
mild detergent.

Air dry completely
before re-use or
storage.

DO NOT

bleach or

iron.

CLEANING PLASTIC

Spot clean using
warm water with
mild detergent.

Towel dry completely
before re-use or
storage.

DO NOT

bleach.

CLEANING BUCKLE AND LOWER ANCHOR CONNECTOR HARDWARE
NOTE:

Buckle should fasten with a “click” if not, rinse under warm running

water. DO NOT use detergents or lubricants.

CARE + MAINTENANCE

0225_MESA_INS_V4.indd 47

3/19/15 11:07 AM

Summary of Contents for mesa




























Search results

Summary of Contents for mesa

Reviews:

Related manuals for mesa

Brands by name

Popular brands

UPPAbaby mesa, Manual

Search results

Summary of Contents for mesa

Reviews:

Related manuals for mesa

Brands by name

Popular brands