UPPAbaby mesa Manual Download Page 2

Page: 2 / 27

TABLE OF CONTENTS

BEFORE YOU BEGIN

CERTIFICATION

USE RECOMMENDATIONS

REGISTRATION

NOTICE OF EXPIRATION

WA GENERAL SAFETY INSTRUCTIONS

VEHICLE COMPATIBILITY

CHOOSING A VEHICLE SEATING LOCATION

DETERMINING BEST INSTALLATION METHOD

BASE INSTALLATION

CARRIER INSTALLATION WITHOUT BASE

OVERVIEW OF LATCH

OVERVIEW OF VEHICLE SEAT BELT SYSTEMS

UNSAFE VEHICLE SEAT BELT S SEATING

BASE INSTALLATION WITH LOWER ANCHORS

LEVELING BASE

BASE INSTALLATION WITH LOWER ANCHORS

SAFETY CHECK

UNINSTALLING BASE

BASE INSTALLATION WITH VEHICLE SEAT BELT

LEVELING BASE

SECURING THE BASE WITH VEHICLE SEAT BELT

SECURING THE BASE (LAP AND SHOULDER BELT INSTALLATION)

SECURING THE BASE (LAP BELT ONLY INSTALLATION)

SAFETY CHECK

UNINSTALLING BASE

REAR-FACING SEAT FEATURES

OVERVIEW OF BASE

OVERVIEW OF CARRIER

Read all instructions before use of the rear-facing car seat.

Keep instruction book for future use.

(Storage pocket located on underside of base.)

0225_MESA_INS_V4.indd 1-1

3/19/15 11:07 AM

Summary of Contents for mesa




























Search results

Summary of Contents for mesa

Reviews:

Related manuals for mesa

Brands by name

Popular brands

UPPAbaby mesa, Manual

Search results

Summary of Contents for mesa

Reviews:

Related manuals for mesa

Brands by name

Popular brands