Uponor T-27 Installation And Operation Manual Download Page 7

Page: 7 / 18

Attach the back plastic cover to the
wall

Wall box mounted

60 mm

SI0000459

Attach the back cover to the wall box.

Wall mounted

SI0000460

60 mm

OPTION

Attach the back cover to the wall with 1 or 2 screws.

Connect the thermostat

Note

Read the wiring diagram in the technical data chapter
before making any electrical installation!

SI0000461

Connect the power cables to the backside of the thermostat. External
sensor is optional.

The cables from the actuators can be connected directly to the
thermostat or to a separate connection box.

For easier wiring, Uponor Base Flexiboard X-24/X-25/X-26/X-27
offers flexible allocation of one or more actuators to the room
thermostats via selector switch during or after installation.

Uponor Base thermostat display T-27 230V

Installation and operation manual

Summary of Contents for T-27



















Search results

Summary of Contents for T-27

Reviews:

Related manuals for T-27

Brands by name

Popular brands

Uponor T-27, Installation And Operation Manual

Search results

Summary of Contents for T-27

Reviews:

Related manuals for T-27

Brands by name

Popular brands