Uponor Smatrix Wave, Quick Manual

Page: 9 / 224

Register thermostat and/or system device
to a controller
N O T E !
At least one thermostat must be registered
before registering a system device.
To register room thermostats and system devices (interface
etc.) to the controller:
Enter registration mode
11. Press and hold the OK button on the controller, for
about 3 seconds, until the LED for channel 1 (or the
fi rst unregistered channel) fl ashes red.
Register a thermostat
12. Select a thermostat channel.
12.1 Use buttons < or > to move the pointer (LED
fl ashes red) to a preferred channel.
12.2 Press the OK button to select the channel for
registration. The LED for the selected channel
starts fl ashing green.
12.3 Repeat steps 12.1 and 12.2 until all channels to
be registered with the thermostat are selected
(LEDs fl ashing green).
Note! It is recommended to register all channels
to the thermostat at the same time.
13. Select a thermostat.
THERMOSTAT T-143 AS A THERMOSTAT, WITH
VARIOUS FUNCTIONS
13.1 Gently press and hold the registration button
on the thermostat, release when the LED starts
fl ashing green (located in the hole above the
registration button).
The selected channel LED in the controller turns
fi xed green and the registration is complete.
THERMOSTAT T-144
13.1 Using a pointed instrument, gently press and hold
the registration button on the thermostat, release
when the LED above the dial starts fl ashing.
The selected channel LED in the controller turns
fi xed green and the registration is complete.
THERMOSTAT T-145
13.1 Gently press and hold the registration button
on the thermostat, release when the LED on the
front of the thermostat starts fl ashing.
The selected channel LED in the controller turns
fi xed green and the registration is complete.
THERMOSTATS T-146, T-148 AND T-149
13.1 Press and hold both - and + buttons (T-149
= and ) on the thermostat until the text
CnF (confi gure) and a communication icon is
displayed.
The selected channel LED in the controller turns
fi xed green and the registration is complete.
14. Repeat steps 12 and 13 until all available thermostats
are registered.
Register a system device
15. Make sure to be in registration mode (step 11).
15.1 Use buttons < or > to move the pointer to the
power LED (LED fl ashes red).
15.2 Press the OK button to enter system channel
registration mode. The power LED fl ashes
according to the pattern long blink, short pause,
long blink and channel 1 LED fl ashes red.
15.3 Select a system channel, see list below.
1 = Timer
2 = Not used
3 = Public thermostat with outdoor sensor
4 = Not used
5 = Public thermostat with Comfort/ECO switch
15.4 Press the OK button to select system device
channel. The channel LED starts fl ashing green
16. Select a system device matching the system channel.
TIMER I-143
16.1 Press and hold both - and + buttons on the
thermostat until the text CnF (confi gure) and a
communication icon is displayed.
The selected channel LED in the controller turns
fi xed green and the registration is complete.
THERMOSTAT T-143 AS A SYSTEM DEVICE, WITH
VARIOUS FUNCTIONS
16.1 Gently press and hold the registration button
on the thermostat, release when the LED starts
fl ashing green (located in the hole above the
registration button).
The selected channel LED in the controller turns
fi xed green and the registration is complete.
17. Repeat steps 15 and 16 until all available system devices
are registered.
Exit registration mode
18. Press and hold the OK button on the controller, for
about 3 seconds, until the green LEDs turn off to end
registration and return to run mode.
Q U I C K G U I D E
9
U P O N O R S M AT R I X B A S E · Q U I C K G U I D E
UK
CZ
DE
DK
EE
ES
FI
FR
HR
HU
IT
LT
LV
NL
NO
PL
PT
RO
RU
SE
SI
SK