Uponor Smatrix Base PRO R-147 KNX Installation And Operation Manual Download Page 4

This installation and operation manual describes how 
to install and operate the Uponor Smatrix Base PRO 
Gateway Module R-147 KNX.

2.1  Safety instructions

Warnings used in this manual

The following symbols are used in the manual to 
indicate special precautions when installing and 
operating any Uponor equipment: 

W

arning

!

Risk of injury. Ignoring warnings can cause 
injury or damage components.

C

aution

!

Ignoring cautions can cause malfunctions.

Safety measures

Conform to the following measures when installing and 
operating any Uponor equipment:

•  Read and follow the instructions in the installation 

and operation manual.

•  Installation must be performed by a competent 

person in accordance with local regulations.

•  It is prohibited to make changes or modifications 

not specified in this manual.

•  All power supplies must be switched off before 

starting any wiring work.

•  Do not use water to clean Uponor components.

•  Do not expose the Uponor components to 

flammable vapours or gases.

Uponor cannot accept any responsibility for damage 
or breakdown that can result from ignoring these 
instructions.

Power

W

arning

!

The Uponor system uses 50 Hz, 230 V AC 
power. In case of emergency, immediately 
disconnect the power.

Technical constraints

C

aution

!

To avoid interference, keep installation/data 
cables away from power cables of more than 
50 V.

2.2  Correct disposal of this product 

(Waste Electrical and Electronic 
Equipment)

N OT E !

Applicable in the European Union and other 
European countries with separate collection 
systems

This marking shown on the product or its 

literature indicates that it should not be 
disposed with other household wasted at the 

end of its working life. To prevent possible harm to the 
environment or human health from uncontrolled waste 
disposal, please separate this from other types of wastes 
and recycle it responsibly to promote the sustainable 
reuse of material resources.

Household users should contact either the retailer 
where they purchased this product, or their local 
government office, for details of where and how they 
can take this item for environmentally safe recycling.

Business users should contact their supplier and check 
the terms and conditions of the purchase contract. This 
product should not be mixed with other commercial 
wastes of disposal.

2  Preface

UK

CZ

DE

DK

EE

ES

FI

FR

HR

HU

IT

LT

LV

NL

NO

PL

PT

RO

RU

SE

SK

4

U P O N O R   S M AT R I X   B A S E / B A S E   P R O   ·   I N S TA L L AT I O N   A N D   O P E R AT I O N   M A N UA L

Summary of Contents for Smatrix Base PRO R-147 KNX



























Reviews: