Uponor Smatrix Base PRO R-147 KNX Installation And Operation Manual Download Page 3

1  Copyright and disclaimer

Uponor has prepared this installation and operation 
manual and all the content included solely for 
information purposes. The contents of the manual 
(including graphics, logos, icons, text, and images) 
are copyrighted and protected by worldwide copyright 
laws and treaty provisions. You agree to comply with 
all copyright laws worldwide in your use of the manual. 
Modification or use of any of the contents of the 
manual for any other purpose is a violation of Uponor’s 
copyright, trademark and other proprietary rights.

The presumption for the manual is that the safety 
measures have been fully complied with and, further, 
that Uponor Smatrix Base, including any components 
that are part of such system, covered by the manual:

•  is selected, planned and installed and put into 

operation by a licensed and competent planner and 
installer in compliance with current (at the time 
of installation) installation instructions provided 
by Uponor as well as in compliance with all 
applicable building and plumbing codes and other 
requirements and guidelines;

•  has not been (temporarily or continuously) exposed 

to temperatures, pressure and/or voltages that 
exceed the limits printed on the products or stated 
in any instructions supplied by Uponor;

•  remain in its originally installed location and is not 

repaired, replaced or interfered with, without prior 
written consent of Uponor;

•  is connected to potable water supplies or 

compatible plumbing, heating and/or cooling 
products approved or specified by Uponor;

•  is not connected to or used with non-Uponor 

products, parts or components except for those 
approved or specified by Uponor; and

•  does not show evidence of tampering, mishandling, 

insufficient maintenance, improper storage, neglect 
or accidental damage before installation and being 
put into operation.

While Uponor has made efforts to ensure that the 
manual is accurate, Uponor does not guarantee or 
warrant the accuracy of the information contained 
herein. Uponor reserves the right to modify the 
specifications and features described herein, or 
discontinue manufacture of Uponor Smatrix Base 
PRO Gateway Module R-147 KNX described at any 
time without prior notice or obligation. The manual 
is provided “as is” without warranties of any kind, 
either expressed or implied. The information should be 
independently verified before using it in any manner.

To the fullest extent permissible, Uponor disclaims 
all warranties, expressed or implied, including, 
but not limited to, the implied warranties of 
merchantability, fitness for particular purpose and 
non-infringement.

This disclaimer applies to, but is not limited to, the 
accuracy, reliability or correctness of the manual.

Under no circumstances shall Uponor be liable for 
any indirect, special, incidental or consequential 
damages or loss that result from the use of or 
the inability to use the materials or information 
in the manual, or any claim attributable to errors, 
omission or other inaccuracies in the manual, even 
if Uponor has been advised of the possibility of 
such damages.

This disclaimer and any provisions in the manual 
do not limit any statutory rights of consumers.

UK

CZ

DE

DK

EE

ES

FI

FR

HR

HU

IT

LT

LV

NL

NO

PL

PT

RO

RU

SE

SK

3

U P O N O R   S M AT R I X   B A S E / B A S E   P R O   ·   I N S TA L L AT I O N   A N D   O P E R AT I O N   M A N UA L

Summary of Contents for Smatrix Base PRO R-147 KNX



























Reviews: