Uponor 102628 Installation And Operation Manual Download Page 4

4  l  Uponor Combi Port PRO XU  l  Installation manual

In the case of installations in the public sector (multi family homes, 
hotels, retirement homes, hospitals, sports halls, etc.) care must be 
taken to ensure that the heated drinking water temperature does not 
fall below 60°C and the circulating water re-entering the unit reaches 
a minimum temperature of 55°C. This requires accurate calculation 
and precise adjustment of the circulating line.

The system is maintained in compliance with DIN EN 806-5 or, outside 
Germany, in accordance with national regulations or standards.

Use-related wear of wearing parts, such as pumps, built-in valves 
(moving parts, PM valves, etc.) are not considered as defects.

We recommend a maintenance cycle especially for example for the 
built-in heat exchanger (test, dirt, sludge, lime), PM valve (functional 

WHVWGLUW¿OWHUVKXWRႇYDOYHVIXQFWLRQDOWHVWYDOYHVVXFKDVD

thermostatic lead module, thermostatic hot water temperature limiter, 

]RQHYDOYHVLQMHFWLRQYDOYHGLႇHUHQWLDOSUHVVXUHUHJXODWRUSXPS

volume measuring unit, thermal premixer or other parts.

5  Please instruct the system users properly and provide them with 

these installation and operating instructions together with the 
inventory documents.

 

Please check that the units are complete. Any screws that 
are loosened during transport should be retightened.

 

In the event of leaks that occur during the pressure test, be 

VXUHWRGHSUHVVXULVHWKHXQLWEHIRUHUHSODFLQJDQ\DႇHFWHG

components.

 

Never remove individual parts of the unit (or any other built-in 
components) while the system is still under pressure (risk of injury).

 

If you have any questions about correct operation or function, 
please contact your supplier. Of course you are also welcome 
to contact us directly anytime.

1.1 

Validity of the instructions

These installation and operating instructions apply exclusively to 
the manufacturer’s unit. The type can be found on the ID plate.

The ID plate is located on the base plate of the unit. The ID plate 
contains the following information. 

•  Sales

•  Created by

•  Device type

•  Technical data

•  Year built

•  Serial number

•  Order number

•  Production location

1.2 

ID plate (example)

Device type:

Combi Port PRO XU

Hz-VI temperature: 

max. 95°C

7::ÀRZUDWH

Exchanger type 1; 15 l/min

Pressure level Hz/TWW: 

PN 10/PN 6

Year built:

2020

Serial number: D-10-0026036

Order number: 102628 

Made in Germany

1.3 

Related documents and regulations

•  Additional documents are valid in conjunction with 

these installation and operating instructions.

•  When carrying out service work on the unit, it is essential to 

observe all instructions for supplementary components and 
components of the heating system.

•  In all service work pay attention to:

-  the recognised technical rules for safe and 

professional operations

-  the statutory regulations for accident prevention

-  the statutory environmental protection regulations

-  the stipulations of employer’s liability insurance associations

-  the relevant safety conditions of the DIN, EN, DVGW, DWGW, 

VDE and AGFW standards

-  the relevant national and EU regulations for other countries

 DQGWKHUHOHYDQWVSHFL¿FDWLRQVIRUWKHUHFRJQLVHGUXOHV

of engineering

1.4 

Document retention

•  You should keep these instructions and all other applicable 

documents in a safe place, so that they are always available.

•  Make sure to hand over all the documents to the operator.

1.5 

Correct operation

The heat interface unit is intended exclusively for drinking water 
heating, control of the downstream domestic heating system and 
the measurement of heating energy and cold water consumption 
for an apartment or similar unit.

Any other or further use is considered improper use. The 
manufacturer/supplier is not liable for resulting damages. The risk 
is borne solely by the user. Intended use also includes observance 
of all relevant documents and compliance with the inspection and 
maintenance conditions.

Under no circumstances should you deviate from the values given 
in the technical data.

1.6 

Personnel and qualifications

The heat interface unit may be operated by the operator or by 
personnel authorised by the operator. Service work (assembly, 
commissioning and maintenance) on the heat interface unit 
requires specialist knowledge. In general, only authorised specialist 
tradesmen are allowed to carry out service work on the heat 
interface unit. 

Summary of Contents for 102628





































Reviews: