background image

© UPLIFT Desk

 • 1-800-349-3839 • [email protected] • www.upliftdesk.com

5

G. 

Slide one Crossbar rail (part 6)   

and the Open-end rail (part 7) into  
the Corner leg assembly and the  
Right leg assembly.

6

7

F. 

In this step, you’ll be attaching the feet to the legs. Before you begin this step, consider where you 

plan to sit at your desk. Consider your work style, desktop equipment, and where you want your leg space.

If you’ll be sitting on an 
outer end and need leg 
room there, attach the 
Small foot (part 3) to 
one of the outer legs.

Once you’ve decided where you want the feet to 
be, attach each Foot (part 2) and the Small foot 
(part 3) to the legs you have chosen with four (4) 
M6x14 Machine screws (part 15) and tighten in a 
cross pattern. Be sure to point long end of foot 
in the same direction as the long end of the side 
bracket

If you’ll be sitting inside 
the corner, attach the 
Small foot (part 3) to 
the center leg, in the 
corner.

+

+

H. 

Lay down a blanket. Place your desktop 

on it (to protect it from scratches) with the 
pre-drilled holes facing UP. Slide the smaller 
Return desktop (part 21) and meet it against 
the Main desktop (part 20).

or

2

3

15

20

21

I. 

Make sure both Main and Return desktops 

are flush. Line up the Support brackets (part 18) 

over their corresponding pre-drilled holes.

Screw two (2) #10x5/8’’ Wood screws (part 17a) 
all the way into the Support bracket on the side 

overlapping the Main desktop (part 20)(fig. 1). 

On the Return desktop (part 21) carefully align 
and insert a third Wood screw (part 17a) 
through a hole, but only partway. This is only 
to keep the Return desktop from moving around 

(fig. 2). You will remove this third screw in a later step.

(fig 1)

(fig 2)

20

21

18

17 a

Summary of Contents for 3-Leg Desk













Reviews: