background image

8

DISPLAY IN EITHER DEGREES CELSIUS/FAHRENHEIT

The thermostat can display the ambient temperature and the set point in degrees 

Celsius (standard factory setting) or Fahrenheit.
1.  To switch from degrees Celsius to degrees Fahrenheit and vice versa, simulta-

neously press down the two buttons for 3 seconds. Once the three seconds are 

over the °C or °F symbol will flash. Release the buttons.

2.  Press down the top button to switch from the degrees Celsius to the degrees 

Fahrenheit, and conversely. The degree Celsius or Fahrenheit symbol will be 

displayed.

3.   When the adjustment is completed, release the buttons and wait for 5 seconds 

to exit the adjustment function.

HEATING POWER INDICATOR

The level of power used to maintain the temperature at the set point is expressed 

as a percentage indicated by the number of bars in the thermometer displayed. The 

heating power used is displayed as follows:

4 bars = 75% to 100%
3 bars = 50% to 75%
2 bars = 25% to 50%
1 bar = 1% to 25%
0 bar = no heat

FROST-FREE WARNING 

The Snowflake icon is displayed when the temperature set point is between 3°C 

(37°F) and 5°C (41°F). A minimum temperature will be maintained to ensure frost 

control.

Summary of Contents for UT202NP













Reviews: