background image

1 - Delivery and warranty 

 

1.1 - Foreword 

  

WARNING! 

The symbols used in this manual draw the reader’s attention to points and 
operations that are hazardous to the operator’s personal safety or that risk 
damaging the machine. 
Do not use the machine unless you have read and properly understood these 
notes. 

  
WARNING! 

For reasons of clarity, some of the illustrations appearing in this manual show the 
machine or parts of it with its panels or guards removed. 
Never use the machine in this condition; only use it when it is fully equipped with 
the guards and in good working order. 
  
The manufacturer forbids the reproduction, even partial, of this manual or the use 
of its contents for purposes other than those expressly allowed. 
Any breach in this regard shall be punishable by law. 
  

1.2 - Storing and using this manual 

This manual uses text and illustrations to familiarise users with the machine and 
explain the instructions and essential criteria for its transport, handling, use and 
maintenance. 
Read this manual carefully before using the machine. 
Store this manual with care near the machine so that it can be readily available for 
future reference. 
If the manual is lost or damaged, you can request a copy from your dealer or 
directly from the manufacturer. 
If the machine is transferred to a new owner, the latter’s identification and contact 
details must be notified to the manufacturer. 
The manual reflects the state of knowledge at the time of sale of the machine, and 
cannot be considered inadequate in the light of more recent experience and 
updates. 
The manufacturer reserves the right to update the products and manuals without 
being obliged to update previous products and manuals, except in exceptional 
circumstances. 
In case of doubt, contact your local service centre or the manufacturer. 
The manufacturer is committed to continuously improving its products.  
For this reason, the manufacturer welcomes any reports or proposals geared 
towards improving the machine and/or the manual. The machine is delivered to the 
customer with the warranty conditions applicable at the time of sale. 
Please contact your dealer for any further information. 

 
1.3 - Warranty 

The user is not authorised to tamper with the machine in any way. Contact the 

Summary of Contents for UPASTA

























Reviews: