background image

Press these buttons to toggle the Vintage Preamps. The Vintage Preamps 
can be used on mic, line, and instrument inputs.  

The Vintage Preamp adds a carefully crafted analog tube preamp 

emulation, inspired by Universal Audio’s all

-tube 610 console preamplifier, 

to the sound. When the button is lit orange, the circuit is active.  

(9) 76 Compressor Buttons 

Press these buttons to engage the 76 Compressors. The 76 Compressors 

can be used on mic, line, and instrument inputs. The button is lit orange 
when the compression circuit is active. 

The 76 Compressor lets you add clarity and punch to voice, guitars, and 

more, with an analog compressor based on UA's iconic 1176 Limiting 
Amplifier. 

Press the button repeatedly to cycle through the presets or disable the 
circuit (VOC, GTR, FAST, or OFF).  

Note:

 The input level increases when the compressor is active, so you may 

want to readjust your Gain setting. 

(10) 76 Compressor Presets 

The indicators above the 76 Compressor button indicate whether the 

compressor is off or enabled on one of the presets. The 76 Compressor 
presets have the following characteristics: 

VOC 

Fast attack and slow release for classic smooth vocal 
compression 

GTR 

Slow attack and relatively quick release allows more guitar/bass 
transients 

Summary of Contents for Volt 476


















Reviews: