Universal Audio Volt 476 Hardware Manual Download Page 17 | Manualshive

Page: 17 / 17

background image

Host indicator

doesn’t light

•

Power Volt off and back on.

•

Try a different USB port or USB hub.

•

Try a different USB cable.

Crackling audio,

dropouts,
glitches

Increase the buffer size setting in the software on

your computer. When recording, you can use direct

monitoring to record without latency at higher buffer
sizes.

(PC) ASIO driver

not available in
DAW

Install the Volt hardware driver with the UA Connect
app.

«
...
15
16
17

Summary of Contents for Volt 476


















Reviews:

No comments

Related manuals for Volt 476

Brand: Campbell Pages: 18

Brand: Vector Pages: 4

Brand: Datavideo Pages: 50

Brand: Waterous Pages: 90

Brand: Campbell Pages: 14

Brand: AAON Pages: 36

Brand: Xo Pages: 59

Brand: Maico Pages: 55

Brand: Maico Pages: 38

Brand: Maico Pages: 2

Brand: MAHA Maschinenbau Haldenwang Pages: 13

Brand: PAT Pages: 44

Brand: Park Tool Pages: 4

Brand: Qlight Pages: 4

Brand: Safavieh Pages: 2

Brand: Vendlet Pages: 2

Brand: Park House Healthcare Pages: 32

Brand: Mac Medical Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands