Unitronics Vision V350-35-T2 Installation Manual Download Page 6 | Manualshive

Page: 6 / 10

background image

V350-35-T2 Installation Guide

6

Unitronics

Input wiring npn (sink)

Input wiring pnp (source)

HSC input wiring, npn (sink)

HSC input wiring, pnp (source)

Shaft-encoder

Analog input wiring, voltage/current (4-wire)

Analog input wiring, current (2/3 wire)

Shields should be connected at the signal’s source.
The 0V signal of the analog input must be connected to the controller’s 0V.

«
...
4
5
6
7
8
...
»

Summary of Contents for Vision V350-35-T2











Reviews:

No comments

Related manuals for Vision V350-35-T2

Brand: ABB Pages: 139

Brand: ABB Pages: 28

Brand: ABB Pages: 59

Concord express

Brand: GE Pages: 3

Brand: Harman Kardon Pages: 25

Brand: Uniss Pages: 21

Brand: IFM Pages: 49

Brand: Samson Pages: 78

Brand: Rane Pages: 2

FUTERA XLF Series

Brand: RBI Pages: 128

Brand: S&C Pages: 11

Brand: S&C Pages: 24

Brand: S&C Pages: 19

Brand: Tamas Pages: 12

Brand: WAREMA Pages: 4

U1000 iQpump Drive

Brand: YASKAWA Pages: 426

Brand: YASKAWA Pages: 26

Brand: YASKAWA Pages: 210

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands