Unitronics Samba SM35-J-RA22 Installation Manual Download Page 9 | Manualshive

Page: 9 / 12

background image

Samba™ PLC+ HMI

Unitronics

9

RTD



PT100 (Sensor 0): use Input 9 and 10, related to CM signal.



PT100 (Sensor 1): use Input 7 and 8, related to CM signal.



4 wire PT100 can be used by leaving one of the sensor leads unconnected.

Analog Outputs

Relay Outputs

Increasing Contact Life Span

To increase the life span of the
relay output contacts and protect
the device from potential damage
by reverse EMF, connect:



A clamping diode in parallel with each
inductive DC load



An RC snubber circuit in parallel with each
inductive AC load

«
...
7
8
9
10
11
...
»

Summary of Contents for Samba SM35-J-RA22













Reviews:

No comments

Related manuals for Samba SM35-J-RA22

Brand: Febco Pages: 4

Brand: Cisco Pages: 48

Brand: Value Point Pages: 7

Brand: ZETRON Pages: 3

Brand: ADEMCO Pages: 2

Brand: ABC Design Pages: 38

Brand: easydriver Pages: 26

Brand: Calsense Pages: 10

Brand: ABC Design Pages: 10

Brand: ABC Design Pages: 10

Brand: E+E Elektronik Pages: 20

Brand: Samson Pages: 8

Brand: Samson Pages: 60

Brand: Samson Pages: 40

Brand: ZPA Pecky, a.s. Pages: 36

Brand: Ros Pages: 10

Brand: Anthem Pages: 8

Brand: National Instruments Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands