background image

12100 POLARIZING MICROSCOPE SERIES 

UNITRON

® 

20

MAINTENANCE 

Please remember to 

never

 

leave the microscope with eyepieces removed and always protect the 

microscope with the dust cover when not in use. 

SERVICE 

UNITRON

®

 microscopes are precision instruments which require periodic servicing to keep them 

performing properly and to compensate for normal wear. A regular schedule of preventative maintenance 
by qualified service personnel is highly recommended. Your authorized UNITRON

®

 distributor can 

arrange for this service. Should unexpected problems be experienced with your instrument, proceed as 
follows: 

1. Contact the UNITRON

®

 distributor from whom you purchased the microscope. Some

problems can be resolved simply over the telephone.

2. If it is determined that the microscope should be returned to your UNITRON

®

 distributor or to

UNITRON

®

 for warranty repair, pack the instrument in its original Styrofoam shipping carton. If you no

longer have this carton, pack the microscope in a crush-resistant carton with a minimum of three inches
of a shock absorbing material surrounding it to prevent in-transit damage. The microscope should be
wrapped in a plastic bag to prevent Styrofoam dust from damaging the microscope. Always ship the
microscope in an upright position; 

NEVER SHIP A MICROSCOPE ON ITS SIDE

. The microscope or

component should be shipped prepaid and insured.

LIMITED MICROSCOPE WARRANTY 

This microscope is warranted to be free from defects in material and workmanship for a period of five (5) years for 
mechanical  and  optical  components  and  one  (1)  year  for  electrical  components  from  the  date  of  invoice  to  the 
original (end user) purchaser.  This warranty does not cover damage caused in-transit, misuse, neglect, abuse or 
damage  resulting  from  improper  servicing  or  modification  by  other  then  UNITRON

®

  approved  service  personnel.

This warranty does not cover any routine maintenance work or any other work, which is reasonably expected to be 
performed  by  the  purchaser.  Normal  wear  is  excluded  from  this  warranty.  No  responsibility  is  assumed  for 
unsatisfactory operating performance due to environmental conditions such as humidity, dust, corrosive chemicals, 
deposition  of  oil  or  other  foreign  matter,  spillage  or  other  conditions  beyond  the  control  of  UNITRON  Ltd.    This 
warranty expressly excludes any liability by UNITRON Ltd. for consequential loss or damage on any grounds, such 
as  (but  not  limited  to)  the  non-availability  to  the  End  User  of  the  product(s)  under  warranty  or  the  need  to  repair 
work  processes.    Should  any  defect  in  material,  workmanship  or  electronic  component  occur  under  this  warranty 
contact  your  UNITRON

®

  distributor  or  UNITRON

® 

at  (631)  543-2000.    This  warranty  is  limited  to  the  continental

United States of America.  All items returned for warranty repair must be sent freight prepaid and insured to Unitron 
Ltd.,  73  Mall  Drive,  Commack,  NY  11725 

–  USA.    All  warranty  repairs  will  be  returned  freight  prepaid  to  any 

destination  within the continental United States of America. For all foreign warranty repairs, return freight charges 
are the responsibility of the individual/company who returned the merchandise for repair.   

Summary of Contents for 12100 Series





















Reviews: