background image

© 201

6

 Enviro Water Solutions, 

LLC

3060 Performance Circle, Suite 2, DeLand, FL 32724

Page 4

(855) 498-0023

Product Operation and Specifications

Important Information

Read these instructions carefully and determine the location of all system components before

beginning installation.

Check all applicable plumbing, building, and electrical codes for installation compliance.

Install the system on the main water supply.

Systems that contain electronic components cannot be installed outside in uncovered areas.

WARNING:

If this or any other system is installed in a metal (conductive) plumbing system, i.e. copper or 

galvanized metal, the plastic components of the system will interrupt the continuity of the 

plumbing system. As a result any errant electricity from improperly grounded appliances 

downstream or potential galvanic activity in the plumbing system can no longer ground 

through contiguous metal plumbing. Some homes may have been built in accordance with 

building codes, which actually encouraged the grounding of electrical appliances through the 

plumbing system. Consequently, the installation of a bypass consisting of the same material 

as the existing plumbing, or a grounded "jumper wire" bridging the equipment and re-

establishing the contiguous conductive nature of the plumbing system must be installed prior 

to your systems use.

CAUTION:

When adding a filtration/softening system to homes/buildings supplied by well water, the system should be 
installed following the pressure tank. 

DO NOT USE this system for pneumatic or hydro pneumatic 

applications. If you are using a booster pump, then install this system following the booster 
pump.

 If you have questions, please call 

technical support at 844-663-3078

.

Specification Description

WR

10

PS15

Max Flow Rate

8

 GPM 

15 GPM 

Minimum Working Pressure

25 PSI

Maximum Working Pressure

80 PSI

Maximum Vacuum

5 inch/127 mm Hg

Operating Temperatures

36°F – 120°F

pH Range

6 – 11

United Water Filter 

WR

10/PS15

Premium Whole House Water Filter

/Conditioner

Rev A

Summary of Contents for WR10





















Reviews: