background image

-

3

-

FUEL CONSIDERATIONS

Your pellet stove is designed to burn premium hardwood pellets that comply with the Pellet Fuels Institute(PFI) 

standards (minimum of 40 lbs per cubic ft, 1/4” to 5/16” diameter, length no greater than 1.5”, not less than 8,200 

BTU/lb, moisture under 8%by weight, ash under 1% by weight, and salt under 300 parts per million). Pellets that 

are soft, contain excessive amounts of loose sawdust, have been, or are wet, will result in reduced performance.

Store your pellets in a dry place. DO NOT store the fuel within the installation clearances of the unit or within the 

space required for refueling and ash removal. Doing so could result in a house fire.

SAFETY AND EPA COMPLIANCE

Your pellet stove has been safety tested and listed to ASTM E 1509-2012, ULC-S627-00 

and (UM) 84-HUD by OMNI-Test Laboratories, Inc. Portland, Oregon, USA.

This manual describes the installation and operation of the King model KP130 pellet 

stove.  This  heater  meets  the  2020  U.S.  Environmental  Protection  Agency’s  crib  wood 

emission limits for wood-heaters sold after May 15, 2020. Under specific EPA test conditions 

burning wood pellet fuel this heater has been shown to deliver heat at a rate of 8,932 to 

25,701 Btu/hr. This heater achieved a particulate emissions rate of 1.3 g/hr when tested 

to method ASTM E 2779 / EPA Method 28R and 64% efficiency.

Heating Specifications

Fuel Burn Rate*

1.5 - 5.0 lbs./hr. (0.7 - 2.3 kg/hr)

Burn Time (lowest setting) 80 hrs.

Hopper Capacity

130lbs. (59kg)

Dimensions
Height

34 in. (864mm)

Width

26 in. (660mm)

Depth

26 in. (686mm)

Weight

210 lbs. (95.5kg)

* Pellet size may effect the actual rate of fuel feed and burn times. Fuel feed rates may vary by as much as 20%. 

Use PFI listed fuel for best results.

Electrical Specifications

Electrical Rating

110-120 volts, 60 HZ, 3.0 Amps

Watts (operational)

175 (approx.)

Watts (igniter running) 425 (approx.)

Specifications

WARNING: It is against federal regulations to operate this wood heater in a manner inconsistent with the 

operating instructions in the owner’s manual.

Note: Register your product on line at www.usstove.com. Save your receipt with your records for any claims.

R

Report No:18-439

Summary of Contents for KP130















































Reviews: