background image

Warranty

28

United Spa Controls One Year Limited Warranty  

United Spa Controls warrants, to the original purchaser, the spa control equipment against defects in 

materials or workmanship for a period of fourteen months from date of manufacture. The obligation 

of this warranty shall be limited to repairing or replacing the part, which in the opinion of the company 

shall be proved defective in materials or workmanship. This limited warranty does not include the 

limitations described below.

Limitations  of  Coverage:

  This warranty does not cover failures due to: damage, freezing, power 

failure, power reduction, unusual atmospheric conditions, rust or corrosion, repairs necessary because 

of operator negligence, improper re-packaging, and damage incurred in shipping. This warranty does 

not cover thermostat calibration, plumbing, and expendable items (gaskets, o-rings, filter cartridges).

Acts  Invalidating  Warranty: 

This warranty shall be invalid if this equipment has been subjected 

to alterations, misuse or abuse, improper water chemistry, improper handling, improper installation, 

repairs (or attempted repairs) which in United Spa Controls’ judgment adversely affects the product’s 

performance/reliability, or if the equipment is used for commercial purposes (used for other than single 

family household purposes). Misuse and abuse shall  include application, installation, or operation 

outside  of  the  environment  and  limitations  for  which  it  was  designed. This  warranty  shall  also  be 

invalid if the spa equipment is damaged by earth or ground fill movement, fire, flood, wind, lightning, 

by act of God, accident, or by intentional, reckless, or negligent acts of any person.

Warranty Performance: 

All warranty service and/or replacement of parts must be performed by an 

individual or service company that has been authorized by United Spa Controls. If within the warranty 

period, any such products shall prove defective, it shall be replaced at United Spa Controls’ option as 

follows: 1) The original retail purchaser shall first contact the point of purchase or the installing dealer, 

as soon as possible after discovery of the defect, but in no event later than the expiration date of this 

warranty. Processing claims should be initiated by the point of purchase or the installing dealer. 2) 

A Return Merchandise Authorization (RMA) form must be completed and submitted to United Spa 

Controls by the point of purchase or the installing dealer. 3) United Spa Controls will issue an RMA for 

eligible items that are not out of their warranty period. 4) Defective items may then be packaged along 

with note that contains the issued RMA number and return shipping information in a box marked with 

the issued RMA number and shipped to: United Spa Controls, 5614 E La Palma Ave, Anaheim, CA 

9287. The customer must pay for all shipping charges and no product shall be returned to United Spa 

Controls without prior consent. 5) After receipt of the products, supporting documents, and verification 

of the nature and cause of the defect, United Spa Controls will replace or repair the defective product 

or issue warranty credit for eligible items at United Spa Controls’ option.

Removal  charges,  re-installation  charges,  any  other  associated  labor,  and  freight  charges  to  and 

from  United  Spa  Controls  of  the  failed  part  shall  be  the  purchaser’s  responsibility. Any  warranty 

replacement or repair shall be subject to the terms and condition of this warranty for the remainder 

of the original period of coverage. United Spa Controls reserves the right to inspect any malfunction 

or defect on location.

Disclaimers, Legal Remedies:

 This warranty is limited and shall be in lieu of all other warranties, 

expressed or implied, including but not limited to, any implied warranty or merchantability or fitness 

for a particular purpose. There are no other warranties that extend beyond the description of the face 

hereof. In no event shall United Spa Controls be liable for labor or material charges in connection with 

removal or replacement of the defective products. United Spa Controls is not liable for the incidental 

or consequential damages, loss of profit, loss of time, inconvenience and incidental expenses. Some 

states do not allow the exclusion or limitation of incidental or consequential damages, so the above 

limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you 

may also have other rights, which vary state to state. United Spa Controls reserve the right to change 

its warranty at any time.

Summary of Contents for T8-X Topside































Reviews: