Unitech MS912+ User Manual Download

Page: 52 / 91

© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd

MS912+ User’s Manual

4.2.2.3 Set Bluetooth Device ID

To customize your own Bluetooth device name for the wireless scanner,

please follow below steps:

STEP 1 Default Wireless ID

STEP 2 Set Wireless ID

STEP 3

Scan up to 16 alphanumeric characters from Full ASCII Table

(Appendix B)

as your desired ID name.

STEP 4 Set Wireless ID

STEP 5

Scan a desired BT mode in BLUETOOTH PROFILE

(4.2.2)

complete the configuration.

NOTE

：

1. If you have connected the scanner with the host BEFORE customizing

your Bluetooth device name, please remove the device and create a new

connection to make sure device name is refreshed. For PC, it is

recommended to restart the Bluetooth adaptor in order to refresh device

name.

2. At Step 3, the scanner will beep three times as an alert that more than 16

characters are entered.

3. To reset the Bluetooth device name to default (”Wireless

Scanner”),please simply do Step1 & Step 5, skipping Step 2 to Step 4.

Summary of Contents for MS912+











































































Search results

Summary of Contents for MS912+

Reviews:

Related manuals for MS912+

Brands by name

Popular brands

Unitech MS912+, User Manual

Search results

Summary of Contents for MS912+

Reviews:

Related manuals for MS912+

Brands by name

Popular brands