Unique Automation Bathomatic Basic MK3 User Manual Download Page 9

Page: 9 / 12

- 9 -

08/11/2016 12:57

THR CALIBRATION
MIN PUMP DEPTH

– Depth at which recirculation pumps starts

PUMP ENABLED

– Recirculation pump on/off during filling

SET DROP TIME - Perfume drop calibration (factory set for your
bathomatic)
MIN J PUMP DEPTH

– Jet pump minimum depth

SELECT SENSOR

SERVICE

NETWORK RESET
FACTORY RESET

DEMO MODE

SETTINGS

SLAVE ADDRESS

– a system can have up to two auxiliary (slave)

BUI

DEVICE TYPE

– a system needs one master device to operate and

can have up to two slave devices

ABOUT

Firmware version and service contact details

Exit by pressing the menu button

. To move back a step press the menu button also.

Due to a delay in your hot water delivery system there are minimum bath depths for
certain temperatures

. If you are prompted with a mes

sage “DEPTH AND

TEMPERATURE MAY NOT BE ACHIEVED

” this means that that you will need

higher depth for the chosen temperature.

Works only after T° to depth calibration has been run in the service menu.

Summary of Contents for Bathomatic Basic MK3












Search results

Summary of Contents for Bathomatic Basic MK3

Reviews:

Related manuals for Bathomatic Basic MK3

Brands by name

Popular brands

Unique Automation Bathomatic Basic MK3, User Manual

Search results

Summary of Contents for Bathomatic Basic MK3

Reviews:

Related manuals for Bathomatic Basic MK3

Brands by name

Popular brands