Unipower INVC4850H Operating Manual Download Page 13

 

 

INVO SERIES INVERTER/CHARGER 

 

  INSTALLATION & OPERATING MANUAL 

Manual No. INVO-1

 Page 

13 

08/11  invo-man

 

 

 

Load indicator 

The load indicator shows the load percentage in VA or W, whichever is bigger, the overload indicator will 
flash when an overload is present. 

 

Battery Charger 

 

 

Inverter to Charger Transition 

The internal battery charger and automatic transfer relay allow the inverter/charger to operate as 
either a battery charger or an inverter (but not both at the same time).  The inverter/charger 
automatically becomes a battery charger whenever AC power is supplied to its AC input.  The AC 
input is internally connected to the AC output while in battery charger mode. 

 

Charger Terminology 

1.

 

Constant Current Stage -

 During this cycle, the batteries are charged at a constant current. 

2.

 

Constant Voltage Stage -

 During this cycle, the batteries are held at a constant voltage (14.1V 

per 12V block for AGM & GEL, 14.6V per 12V block for FLOODED) and accept whatever 
current (less than the current in CC stage) is required to maintain this voltage. This ensures full 
charging. 

3.

 

Float Stage - 

During this cycle, the batteries are held at the float voltage (13.5V per 12V block). 

4.

 

Whenever the AC is reconnected, the charger will reset the above cycle. 

5.

 

If the charger maintains the float state for 21 consecutive days, the charger will reset the cycle.  

Circuit Breaker 

The inverter/

charger contains one input circuit breaker located on the rear panel of the chassis, next to the 

AC input terminal block. This circuit breaker protects the charger and bypass circuits.  The circuit breaker 
will trigger if the input is over-current.  The circuit breaker is push to reset.

 

Summary of Contents for INVC4850H



















Reviews: