Unipower INV2500-HS-50 Operating Manual Download Page 4

INV2500-HS SERIES

MANUAL

INV2500-HS SERIES INVERTERS & SHELVES

OPERATING MANUAL

1.0   INTRODUCTION

 

 

1.1

  This Operating Manual should be read through carefully before installing and operating 

the INV2500-HS inverter modules and shelves. See Figure 1.

 

1.2

  The INV2500-HS is a 2500 volt-ampere, hot-swap, DC to AC inverter module. It con-

verts a nominal 48VDC input into a 115 or 230VAC output at 50 or 60Hz. These mod-

ules are designed to go into a 19-inch, hot-swap compatible shelf, INVR2U-HS, which 

holds one or two units. When two modules are used in this shelf they are automatically 

connected in parallel and synchronized to produce 5000 volt-amperes at 115VAC output 

(44 amperes) or 230VAC output (22 amperes). Or they can be operated in a 1+1 redun-

dant mode at 2500 volt-amperes.

 

1.3

  The 48VDC nominal input has a range of 42 to 56VDC. The inverters achieve 90% ef-

ficiency and 7VA per cubic inch power density. Input and output are both circuit breaker 

protected. They have high surge capability for starting loads such a motors, but the 

output breaker quickly trips if power attempts to flow back into a faulted inverter.

 

1.4

  These inverters can be paralleled for higher output power or for N+1 redundant applica-

tions. They are fully isolated from the battery. Front panel LEDs indicate inverter status, 

and Form C relay alarm contacts are available on the back. The units are self-cooled by 

internal fans.

 

1.5

  In this manual, unless otherwise stated, INV2500-HS shall generally refer to both 

INV2500-HS and INV2500H-HS (115 and 230VAC) inverter models. Likewise INVR2U-

HS shall generally refer to both INVR2U-HS and INVR2U-HS-H shelf models.

2.0 

IMPORTANT FEATURES

 

 

The following is a summary of the important features of the INV2500-HS module and INVR2U-

HS shelf:

 

 

 

 

•  Two Mounting Positions High: 3.5 Inches

 

 

•  2500VA Output for INV2500-HS

 

 

•  5000VA Output for Two Units in Shelf

 

 

•  7VA per Cubic Inch Power Density

 

 

•  115VAC Output at 22 or 44 Amperes

 

 

•  230VAC Output at 11 or 22 Amperes

 

 

•  Low Distortion 50 or 60Hz Sine Wave

 

 

•  42 to 56VDC Input

 

 

•  Fully Isolated from Battery Input

1

Summary of Contents for INV2500-HS-50
























Reviews: