Unipower INV2500-HS-50 Operating Manual Download Page 10

INV2500-HS SERIES

MANUAL

8.4 

On the back panel to the left are the AC output screw terminals. At the center is a termi-

nal strip with the Form C relay contacts N.O., C and N.C. for each side (A and B) of the 

inverter system. To the right are the input bus bars with no. 1/4-20 studs. At the lower far 

right is the no. 10-32 stud chassis ground connection.

9.0   ELECTRICAL SPECIFICATIONS OF INVERTER MODULES

Specifications typical at 48V input, full load and 25°C unless otherwise noted. 

INPUT

Voltage Range .......................................................42-56 VDC ....................................... 42-56 VDC

Input Current, Full Load, 48VDC ...........................<60A DC ........................................... <60ADC

Input Current, No Load, 48VDC ............................<1A DC ............................................. <1ADC

Input Circuit Breaker .............................................100A  ................................................ 100A

EMI Filter, Conducted ............................................................FCC2078 pt.15J Curve A

 

 

EN55022 Curve A

Voice Band Noise/ A-H Battery .............................<32dBrnC/240 .................................. <32dBrnC/240

OUTPUT

Voltage, Full Load .................................................115VAC ............................................ 230VAC

Voltage, No Load  ..................................................120VAC ............................................ 240VAC

Current, Max. .........................................................22A RMS .......................................... 11A RMS

Frequency, ± 0.1% ................................................50 or 60Hz ........................................ 50 or 60Hz

Total Harmonic Distortion ......................................................................<2%

Load Crest Factor .............................................................................. 2.8 to 1

Output Circuit Breaker ........................................................................... 25A

Surge Capability .............................................................................. Up to 300%

Reactive Loads ....................................................................+90° to - 90° Phase Angle

Efficiency ...............................................................................................90% 

SAFETY STANDARDS

 

 .............................................

UL1950, CSA22.2 No.950,  

 

 

EN60950              

STATUS INDICATORS

Input OK .......................................................................................... Green LED

Sync OK .......................................................................................... Green LED

Output OK ....................................................................................... Green LED

Form C Relay Alarm Contacts ....................................................Inverter Fail Alarm

ENVIRONMENTAL

Operating Temp. Range ..................................................................0°C to 70°C

Output Current Derating ......................................................... 2.5%/°C, 50°C to 70°C

Storage Temp. Range .................................................................. -40°C to +85°C

Humidity ............................................................................ 0% to 95%, Non-Condensing

Cooling ............................................................................................Internal Fan

PHYSICAL SPECIFICATIONS

Case Material ................................................................................... Aluminum

Finish, Front Panel & Shelf ........................................................Powder Coat Gray

Dimensions, Inches (mm)

     Module ........................................................................... 3.32 H x 8.50 W x 12.00 D

 

 

(84.3 x 216 x 305)

     Shelf .............................................................................. 3.46 H x 18.32 W x 16.38 D

 

 

(87.9 x 465 x 416)

     Rack Mounting Width .............................................................. 19 or 23 Inches

INV2500-HS

INV2500H-HS

7

Summary of Contents for INV2500-HS-50
























Reviews: