S TO R AG E :
1) Before storing, place the product on a clean, level area. Clean with mild soap and water and allow to dry completely. Apply PVC safe UV
Protectant to all surfaces of the product before deflating.
2) Remove all attachments and store in a sealed container (i.e. a plastic covered box or bin).
3) Remove ALL of the air from the tube using the deflation end of the high output inflator/deflator. If some air is left in the tube, it may freeze
causing cracking.
4) Fold the deflated tube in half (width), then roll loosely toward the valve.
5) Store the product out of direct sunlight and protected from the environment in a clean, dry location. It is best to store inside a container with moth
balls to prevent damage from rodents. NEVER store uncovered, in a damp location, or on a concrete surface! NEVER store at temperatures
below 40 degrees F.
WO R K S PAC E A N D TO O L S :
1) Take care to position yourself in a clean, dry area with good ventilation. For proper curing of adhesives, temperature should remain above 10°C
(50 F). In most cases you will need enough room to inflate the product.
2) Repair Kit Contents: PVC Patch material, PVC Glue, glue brush, glue applicator, pencil, and rubbing alcohol.
3) Additional items that MAY be needed: Air pump, sharp scissors and/ or razor knife, dish washing liquid, water, small bowl or spray bottle, 120 Grit
sandpaper, solvent such as MEK (Methyl Ethyl Ketone), clean dry cloth.
L O CAT E L E A KS :
REPAIR INSTRUCTIONS
WA R R A N T Y:
WARRANTY
PG
7
The Entertainment Group warrants this product to be free of defects in material or workmanship to the original purchaser for two (2)years.
This warranty is subject to the following limitations:
1) Warranty is valid only with dated proof of purchase in the form of the original invoice.
2) Union will make the final warranty determination which may require inspection and/or photos of the product which clearly show defect(s). We
require the above be sent to another location of our choice, freight prepaid, or by email to [email protected]
3) If a product is deemed to be defective by Union the warranty covers the repair or replacement of the defective product only. Union will not be
responsible for any costs, losses, or damages incurred as a result of loss of use of product.
4) This warranty does not cover damage caused by misuse, abuse, neglect, or normal wear and tear, including, but not limited to, punctures, dragging
the product over the ground, damage due to excessive sun exposure or seam failure due to over inflation in the sun, damage caused by improper
handling and storage, damage caused by use in waves or shore break, and damage caused by anything other than defects in materials and
workmanship.
5) This warranty is voided if any unauthorized repair, change, or modification has been made to any part of the equipment. Authorization for such must
come in writing from Union.
6) The warranty for any repaired or replacement equipment is good from the date of the original purchase only.
7) Any warranty claims must be accompanied by the original purchase receipt. The date of purchase must be clear and legible. Serial Number
All Union products are marked with a serial number near the main inflation valve (#1). The serial number may be stamped into the PVC directly around
the valve, or it may be visible on a welded plate near the valve. Please include this number when you contact Union or your dealer, with any
warranty claim.
1) If there is a problem with air leaks, you will need to locate the leak(s) first.
2) Inflate your Union feature product fully. Some small leaks can close themselves at lower air pressures, so it is best to maintain full pressure by
re-inflating periodically while checking for leaks.
3) Use a soapy water solution (50%/ 50% dish soap & water) and a cloth to check for leaks. Work slowly around the product spraying or
swabbing-on soapy water solution. Look for growing bubbles, which indicate a leak.
4) Once a leak is confirmed, dry the area well, mark it and prepare to patch.
5) Use solvent (MEK or Rubbing Alcohol) and a fresh cloth to clean the area to be patched, removing all debris.
6) Dry-fit the patch again and use pencil (provided) to carefully outline where the patch will be located.
7) Next, use the glue and glue brush (provided to spread glue. Try to work neatly and quickly.
8) Using disposable brush, apply a thin, even layer of glue to the repair area making sure to cover the area completely. Stay INSIDE the pencil outline.
9) Using disposable brush, apply a thin, even layer of glue to the to the back of the patch making sure to cover the area completely.
10) Allow glue to cure for approximately 60 seconds.
11) Starting at one corner, carefully align the patch over the repair area using the pencil outline as a guide. Once the two surfaces touch,
the bond will be immediate, so take care.
12) Starting at one corner and working outward, carefully apply the patch to the repair area using very firm pressure.
13) Rub the entire patch area using the glue applicator and the edges of the patch using very firm pressure.
14) Allow to cure for at least 24 hours before inflating.
