Union Community UBio-X Pro2 User Manual Download Page 16

Page: 16 / 89

UBio-X Pro2 User Guide

UNIONCOMMUNITY Co., Ltd.
Addr : 12F, Munjeong Daemyeong Valeon bldg, 127 Beobwon-ro Songpa-gu,

Seoul, Korea (zip code: 05836)

Tel: +82-2-6488-3000, Fax: +82-2-6488-3099,

E-Mail :[email protected]; http://www.unioncomm.co.kr

1.5. Beep sound in operation

Pick

Notice
for reading

the card
or fingerprint

When the card was read

When the fingerprint was entered in the fingerprint

window

Pi-pick

Notice for fail

When the authentication was failed (at Voice off)

Peek

Notice

for Success

When the authentication was successful (at Voice off)

1.6. How to register and authorize the face properly



Face registration method

- Maintain the distance between the terminal and face in about 50 cm.

(Locate the face in the guide line of LCD window.)

- Register the face pose along with the guidance. During the shooting, please

maintain the attention.

- When registering the face, register after sweeping your hair up not to hide the

eyebrow or lower face with your hair or hat. (On the stand of passport picture).



Face authentication method

Just stare at the camera from the front.



Notes

- It is recommended to register and authorize at the location where the terminal is

installed.

- If you pose differently with the registered face, the recognition rate of face can

decrease. It is good to locate the full face as much as possible

- The thick glasses frame or sun-glasses can decrease the recognition rate of face



Cautions in the installation

- Be sure to install the terminal indoor.
- Do not install under the light bulb.

- Not recommended in the circumstance of backlight or direct light.

1.7. Proper fingerprint registration and input methods



Correct fingerprint registration methods

Place your index finger on the window just as you do with a finger stamp.

Do not use the tip of the finger.

Make sure the center of your finger touches the window.

Summary of Contents for UBio-X Pro2

























































































Search results

Summary of Contents for UBio-X Pro2

Reviews:

Related manuals for UBio-X Pro2

Brands by name

Popular brands

Union Community UBio-X Pro2, User Manual

Search results

Summary of Contents for UBio-X Pro2

Reviews:

Related manuals for UBio-X Pro2

Brands by name

Popular brands