Unigreen Mistblowers AP APC Use And Maintenance Manual Download Page 4

4

  unigreen

Thank you for having chosen UNIGREEN.
The product you purchased has been designed and built with the greatest atten-
tion to the safety of the operator and the environment, nevertheless there are
still some residual risks due to the nature of the product used.
For this reason we recommend reading all of this manual to avoid making mis-
takes in the first period of use and to get the most out of the working life of the
atomiser in time, doing the programmed maintenance at regular intervals.

1

USING AND KEEPING THE USE AND MAINTENANCE MANUAL

The manual is an integral part of the machine and should be kept in a safe
place where it can be reached easily for consultation.

1.1

COMPOSITION OF THE MANUAL

This manual consists of various parts to make it easier to consult by subject
and to avoid repetitions; the following are part of the manual:

a)

pump handbook

b)

pressure regulator handbook (manual or electric)

c)

spraying computer handbook (if fitted)

d)

optional accessories handbooks (marker, premix, cardan shaft, etc.)

UNIGREEN reserves the right to make changes to the manual without prior
warning and the normal printing cycles may vary slightly.

1.2

GUARANTEE

The enclosed card indicates the conditions of the UNIGREEN guarantee. The
UNIGREEN guarantee covers the repair or replacement of parts considered manu-
facturing flaws, according to the unquestionable judgement of UNIGREEN, only
after the authorised agent for that zone has verified the fault.

Ambit of the guarantee

The guarantee doesn’t cover cases of normal wear, negligent use, poor mainte-
nance and/or improper use.

The following materials subject to normal wear are not covered by the
guarantee: 

gaskets and seals, diaphragms, seal rings, tubes and pipes, noz-

zles, pressure gauges, oil, tyres, friction material of the clutches.

Evident cases of negligence include:

work speed over that indicated in the spraying tables in the handbook (or too
high for the conditions of the terrain), power-takeoff speed over 540 rpm and
anything else indicated in the Use and Maintenance Manual.

Maintenance:

The guarantee is void if the maintenance indicated in the tables in this manual
isn’t respected, regarding the period and deadline of the interventions, washing
the machine and the circuit at the end of the treatment.

Improper use:

The use the UNIGREEN machines are designed for is indicated in this manual,
any other use is forbidden and makes the guarantee void.

1.3

PRODUCT RESPONSIBILITY

UNIGREEN spa is not responsible if:

a)

During the working life of the machine the normal maintenance operations

aren’t performed and documented as indicated in this handbook, in the en-
closed handbooks of the pumps-motors-regulators-etc. and in any case as is
customary for the normal maintenance of mechanical machinery.

b)

The machine is equipped with non original accessories or components or

parts that aren’t acknowledged by UNIGREEN as their own.

c)

The machine is equipped with original accessories or components that are

unsuitable in the measurements, weight or version for the same.
Please consult the page of available and recommended fittings.

d)

Not following the instructions in the manual whether totally or partially.

e)

Modifications made to the machine that haven’t been authorised by

UNIGREEN.

1.4

WARNING SIGNS IN THE MANUAL AND ON THE MACHINE

Below you will find all of the pictograms on the machine (see FIG.1 for their po-
sition), in order to illustrate the warnings, the prohibitions and the correct
method of use.
The operations that require particular attention are shown in the images beside
the text.

Composite handbook, consult
the specific files on the various
components

Summary of Contents for Mistblowers AP APC









































Reviews: