background image

unigreen     

5

2

SAFETY REGULATIONS AND RESIDUAL RISKS

In relation to safety, the following terms will be used:
Dangerous zones: any zone inside and/or near the machine where the
presence of a person exposed constitutes a risk for the safety and health of
the same person.
Person exposed: any person who has their body or any part of their body in a
dangerous zone.

Before starting the machine, the operator must check for any visible faults in
the safety devices and the machine itself.
Never start the machine until you have told anyone in the range of action of
the machine to move away and they have done so.
The protective devices must not be removed or disabled when the machine is
running.
It is obligatory to keep all the plates with danger and safety signs in perfect
conditions. If they get damaged or deteriorate, replace them in good time.
Replace parts believed to be faulty with others indicated by UNIGREEN.
NEVER try makeshift or hazardous solutions.
Don’t wear clothes, jewellery, accessories, or anything else that can get
caught in the moving machine members.
Pay the greatest attention to all the warning and danger signs on the
machine.
Don’t use the machine for any other purpose other than that indicated in the
manual.
The machine has been designed and built with the appropriate devices to
guarantee the safety of the user.
In any case there are some residual risks associated with the improper use
of the machine by the operator; for this purpose danger signs and symbols
and prohibitions are applied near some parts of the machine (see previous
pictograms).

Key to the symbols

1- Read the Use and Maintenance manual
2- Stop the machine and read the manual before
every intervention
3- Don’t lubricate while running
4- Don’t drink
5- Don’t dispose of residue liquids in the environment
6- No smoking
7- Danger, risk or injury, don’t get near the machine
until the moving machine members have stopped
8- Danger of crushing, don’t get your hands near the
moving mechanical machine members
9- Danger, risk or injury caused by fluids under
pressure
10- Don’t climb on the machine during work or
transfers
11- Don’t climb on the tank
12- Don’t enter in the tank
13- Wearing earmuffs is obligatory
14- Wearing a face mask is obligatory
15- Wearing safety footwear is obligatory
16- Wearing protective gloves is obligatory
17- Wearing protective overalls is obligatory
18- Use a working pressure under that indicated in
red on the manometer.
19- Don’t get your hands near the moving cardan
shaft
20- Make sure power-takeoff of the tractor turns in the
right direction and runs at the right speed.
21- Beware of the possibility of the raised boom
falling
22- Danger of contact with the electric power lines
23- Don’t stand between the machine and the tractor
24- Danger of lateral skidding

2

1

6

3

4

5

8

7

12

9

10

11

14

13

18

15

16

17

INDICATIVE POSITION
OF THE WARNING SIGNS ON THE SPRAYER
NB: the position may vary on the basis of the
characteristics of the model.

20

19

22

21

23

24

21+22

11+12

8+23+24

19+20

da 1 a 18

FIG.1

Summary of Contents for Campo 11





































Reviews: