manualshive.com logo in svg

Unigas K890A, Manual Of Installation - Use - Maintenance

The Unigas K890A user manual, encompassing detailed instructions for installation, use, and maintenance, is available for immediate download, free of charge. Make the most of this comprehensive manual to effortlessly set up and maintain your Unigas K890A, ensuring its optimal performance. Download it now at manualshive.com.

Share
Download
background image

2

INDEX

MICROPROCESSOR CONTROLLED SYSTEM............................................................................................................................  6

User interface..................................................................................................................................................................................  6

Parameters level (heating engineer)...............................................................................................................................................  8

Setting menu...................................................................................................................................................................................  9

Block 000: Internal Parameter ......................................................................................................................................................  10

Block 100: General information.....................................................................................................................................................  10

Block 200: Burner control............................................................................................................................................................... 13

Block 400: Setting air/fuel ratio curves..........................................................................................................................................  25

Block 500: Air/fuel ratio control  ..................................................................................................................................................... 26

Block 600: Actuators .....................................................................................................................................................................  28

Block 700: Error history.................................................................................................................................................................  31

Block 900: Process data ...............................................................................................................................................................  32

Actuators references.....................................................................................................................................................................  33

Gas proving system ......................................................................................................................................................................  33

Air-fuel curve points ......................................................................................................................................................................  33

COMMISSIONING THE BURNER................................................................................................................................................  34

Warm setting.................................................................................................................................................................................  38

Cold setting ...................................................................................................................................................................................  39

BURNER STARTUP WITH LMV2x ALREADY PROGRAMMED ................................................................................................. 40

Reset / manual lockout  ................................................................................................................................................................. 42

Timeout for menu operation..........................................................................................................................................................  42

Entering the Parameter levels ....................................................................................................................................................... 43

Info level........................................................................................................................................................................................  44

Service level .................................................................................................................................................................................. 46

PHASES LIST ............................................................................................................................................................................... 47

BACKUP PARAMETER WITH AZL2x ..........................................................................................................................................  48

RESTORE PARAMETER FROM AZL2x TO LMV.. ...................................................................................................................... 49

WIRING DIAGRAM.......................................................................................................................................................................  65

Wiring connection for LMV20........................................................................................................................................................  65

Wiring variants for LMV27.............................................................................................................................................................  66

Wiring variants for LMV26.............................................................................................................................................................  67

Wiring variants for LMV37.............................................................................................................................................................  68

Summary of Contents for K890A






































































































































Reviews:

No comments

Related manuals for K890A

Omcan 23633 Instruction Manual preview
23633
Brand: Omcan Pages: 12
Unigas HTP2000 Installation Manual preview
HTP2000
Brand: Unigas Pages: 132
Hauck BCS-3000M Instructions Manual preview
BCS-3000M
Brand: Hauck Pages: 20
Riello RDB2.2 SAVANNAH B20 Installation, Use And Maintenance Instructions preview
RDB2.2 SAVANNAH B20
Brand: Riello Pages: 28
Riello RDB2.2 BF GREENSTAR HEATSLAVE II 12/18 Installation, Use And Maintenance Instructions preview
RDB2.2 BF GREENSTAR HEATSLAVE II 12/18
Brand: Riello Pages: 32
Unigas HR512A Manual Of Installation, Use And Maintenance preview
HR512A
Brand: Unigas Pages: 56
Wayne MSR-DC Manual preview
MSR-DC
Brand: Wayne Pages: 6
IHP DUALBURNEROD24N Assembly, Installation And Operation Instructions preview
DUALBURNEROD24N
Brand: IHP Pages: 14
baltur GI 1000 LX Instruction preview
GI 1000 LX
Brand: baltur Pages: 108
Riello Burners RL 250 Installation, Use And Maintenance Instructions preview
RL 250
Brand: Riello Burners Pages: 52
Brentwood TS-300 Operating And Safety Instructions preview
TS-300
Brand: Brentwood Pages: 5
Weil-McLain RIELLO 40 BF UltraOil 800060000-Brn-PO Rie BF5 Installation And Operating Manual preview
RIELLO 40 BF UltraOil 800060000-Brn-PO Rie BF5
Brand: Weil-McLain Pages: 19
VOCHE VH124 Manual preview
VH124
Brand: VOCHE Pages: 5
EdgeStar ESB1LP Owner'S Manual preview
ESB1LP
Brand: EdgeStar Pages: 34
Bentone B30A2.2H Installation And Maintenance Instruction preview
B30A2.2H
Brand: Bentone Pages: 20
Bentone B 45 A2.2H Installation And Maintenance Instruction preview
B 45 A2.2H
Brand: Bentone Pages: 24
Bentone 354012011601 Installation And Maintenance Instruction preview
354012011601
Brand: Bentone Pages: 24
Bentone B 30 A2.2H Installation And Maintenance Instruction preview
B 30 A2.2H
Brand: Bentone Pages: 40

Brands by name

Popular brands

Load more brands