Unigas K890A Manual Of Installation - Use - Maintenance Download | Manualshive

Page: 88 / 133

background image

40

BURNER STARTUP WITH LMV2x ALREADY PROGRAMMED

Once the LMV turns on, the AZL display will show

The burners is basically factory set. The air/fuel ratio curve is set with the maximum output point P9 a little higher or equal to P0. To
adjust the burner on the plant site, adjust the maximum output point to the flow rate values really requested. Then go through the curve-
points, by pressing “+” several times to reach point P9: then adjust the air actuator position (for the air damper) and the fuel acttuator
(for the butterfly valve, in case of gas or the oil pressure governor incase of oil), by adjusting the fuel flow rate by means of the gas pres-
sure stabiliser (for gas) or the oil pressure governor (for oil), checking the combustion valeus contemporarly. Once the burner is adju-
sted at the maximum output, press “-” for more than 5 seconds to process the curve downwards. The curve is then a straight line: go on
checking the combustion values point by point; change them if necessary and in case linearise the curve again.

Before starting the burner up, press

F

and

A

at the same time

enter the password following the procedure on chapter “Programming LMV2x”.
Press ENTER until the display will show:

Press ENTER again: it will show

press ENTER (InFo)

: the display will show phase 12.

Ph12:

Standby

phase (stationary)

Ph12:

Standby

phase (stationary)

By closing the thermostatic series, the burner startup cycle will take place:
Ph22:

Fan ramp up

phase (fan motor = ON, safety shutoff valve = ON)

Ph24:

Traveling to prepurge position

phase

Ph30:

Prepurge

phase

Ph36:

Traveling to ignition position

phase

Ph38:

Preignition

phase

Ph40:

1st safety time

phase (ignition transformer ON)

Ph42:

1st safety time

phase (ignition transformer OFF), preignition time OFF

Ph44:

Interval1

The startup sequence stops at phase 44.

The burners is lit and is in“P1” position (low flame point):

«
...
86
87
88
89
90
...
»

Summary of Contents for K890A






































































































































Reviews:

No comments

Related manuals for K890A

Brand: Riello Pages: 20

Brand: WarmingTends Pages: 23

Brand: Jackson Grills Pages: 21

Brand: Ecosmar+ Pages: 7

Brand: Wolf Pages: 2

Brand: Qlima Pages: 48

Brand: Xo Pages: 36

Brand: Unigas Pages: 120

Brand: Unigas Pages: 64

Brand: Nu-Way Pages: 18

Brand: Nu-Way Pages: 21

MGN 1350 M3D DLU

Brand: Nu-Way Pages: 22

Brand: Nu-Way Pages: 24

Brand: Nu-Way Pages: 24

Brand: Nu-Way Pages: 32

Brand: Nu-Way Pages: 32

Brand: Nu-Way Pages: 49

Brand: Duluth Forge Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands