Uniden UBC92XLT Owner'S Manual Download Page 15 | Manualshive

Page: 15 / 56

background image

15

Setting Up Your Scanner

These guidelines will help you install and use your
new scanner:
•

If your scanner receives interference or electrical
noise, move the scanner or its antenna away
from the source.

•

To improve the scanner’s reception, use an
optional external antenna designed for multi-
band coverage. (You can purchase this type of
antenna at a local electronics store). If the
optional antenna has no cable, use 50-70 ohm
coaxial cable for lead-in. A mating plug might be
necessary for the optional antennas.

•

Use an optional mono earphone or mono
headset with proper impedance for private
listening. Read the precautions on the inside
front cover of this Owners Manual.

•

Do not use the scanner in high-moisture
environments such as the kitchen or bathroom.

•

Avoid placing the scanner in direct sunlight or
near heating elements or vents.

Using Internal Batteries

You can power your scanner using two alkaline or
rechargeable AA batteries.

Using Non-Rechargeable Batteries

1. Make sure the power is turned off.
2. Slide the battery compartment cover.
3. Before you install alkaline or any other non-

rechargeable batteries, use a pointed object
such as a ballpoint pen to set

REG. ALK. BATT./

NI-MH BATT.

inside the compartment to

REG.

ALK. BATT.

.

Setting Up Your Scanner

«
...
13
14
15
16
17
...
»

Summary of Contents for UBC92XLT

























































Reviews:

No comments

Related manuals for UBC92XLT

Brand: Panasonic Pages: 396

Brand: Kodak Pages: 43

8412447 - I55 - Document Scanner

Brand: Kodak Pages: 93

Digital Science 9520

Brand: Kodak Pages: 139

Brand: Konica Minolta Pages: 40

SL1000 Digital Film Scanner

Brand: Konica Minolta Pages: 152

Trouw Nutrition Agrocares

Brand: Nutreco Pages: 2

Brand: UMAX Technologies Pages: 7

Brand: UMAX Technologies Pages: 16

NETDELIVER @V4800

Brand: Avision Pages: 82

Brand: Avision Pages: 172

OpticFilm 7200i SE

Brand: Plustek Pages: 2

Brand: SCANVIEW Pages: 38

Anyty 3R-HSA651

Brand: 3R Pages: 42

Brand: Radio Shack Pages: 40

Brand: Xerox Pages: 133

Travel Scanner 150

Brand: Xerox Pages: 2

Brand: Uniden Pages: 152

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands