background image

10

5.  Turn 

RF Gain

 to set RF gain sensitivity.

6.  Press 

MIC Gain

 to toggle microphone sensitivity between High 

and Low. (LED on = High; LED off = Low)

7.  Set Backlight color (see page 12).

8.  Set LCD Contrast (see page 13).

9.  Set Brightness (see page 13).

all Channel sCan

When All Channel Scan is on, the radio scans channels until it receives 

a signal. It will move to the next channel if no signal is received after 3 

seconds.
1.  Press 

MEM/SCAN

 once if in CB mode (twice if in MEM mode). 

SCAN

 displays.

2.  The radio begins scanning upward through the channels. 

•  To skip the channel the radio has stopped on, turn 

Channel 

Selector

 clockwise to move to the next channel or counter-

clockwise to move to the previous channel.  The radio continues 

scanning in the selected direction.

•  To change to Memory Channel Scan mode, press 

MEM/SCAN

 

while in All Channel Scan mode (see page 12).

3.  To exit All Channel Scan mode, press 

PTT

9/19/NORM

WEATHER

or 

CB/PA

Weather moDe (WX moDe)

Your radio combines a CB radio with a Weather radio and a Weather Alert 

system. The Weather Alert system sounds a seven-second signal in the 

event of severe weather when you are in CB mode. The Weather radio 

continually broadcasts weather conditions when you are in Weather 

mode. 
1.  Press 

WEATHER

. Your radio is now in Weather radio mode.

2.  Select 1 of 7 weather channels using 

Channel Selector

.

You cannot change ANL or NB settings while in WX mode. The radio will sound an 

alert tone.  

Summary of Contents for BEARCAT 880























Reviews: