background image

22

If static is on 1 handset or in 1 

location: 

If static is on all handsets or in all 

locations:

 

-

Check nearby for one of the 

common interference sources.

 

-

Try moving the handset away 

from a suspected source, or try 

moving the suspected source so 

it’s not between the handset and 

the base.

 

-

There is always more noise at the 

edges of the base's range. If an 

Out of Range

 message displays, try 

moving closer to the base.

 

-

Check near the base for the 

source of interference.

 

-

Try moving the base away from 

a suspected source, or turn off 

the source if possible.

 

-

If the base has an adjustable 

antenna, try raising the antenna 

so it stands straight up.

 

-

If you have any service that uses 

the phone line, you might need 

a filter (see below).

Installing a Line Filter or DSL Filter

Sometimes, broadband Internet services that use the telephone line 

can interfere with phones. One of these services−DSL−often causes 

static on telephones. A DSL filter or telephone line filter usually solves 

this problem. The technician who installed your DSL service might 

have left some filters for you; if not, call your DSL provider or look in 

any electronics store.
Plug the DSL filter into the telephone wall jack and plug your phone’s 

base into the filter. Make a test call to make sure the noise is gone.

Liquid Damage

Moisture and liquid can damage your cordless phone.

 



If the exterior housing of the handset or base is exposed to 

moisture or liquid, wipe off the liquid, and use as normal.

 



If moisture or liquid is inside the plastic housing (i.e. liquid can 

be heard in the phone or liquid has entered the handset battery 

compartment or vent openings on the base), follow these steps:

Summary of Contents for 1035 Series





























Reviews: