unicraft SRHW30, Operation And Maintenance Instruction

Page: 5 / 16

E
2 4
5
1
3
Kg
1 2
GB
EXTREMELY IMPORTANT:
Read these safety instructions carefully in addition to the instructions for use, operation and maintenance. Keep this instructions sheet in an easy
to find place as you may need to use it again.
This jack has been designed for use in the elevation of cars and lorries.
Any other application, beyond the conditions established for use of this jack will be considered inappropriate.
Handle the jack correctly and ensure that all parts are in good condition prior to its use.
Only authorised persons should operate the jack having read carefully and understood the contents of this manual.
Do not modify the jack in any way.
Non-compliance with these rules may result in injury or damage to the user, the jack or the vehicle to be lifted.
The manufacturer accepts no responsibility for the improper use of the jack.
1 SAFETY INSTRUCTIONS
1.1 The vehicle to be lifted should never exceed the rated capacity of the jack.
1.2 The maximum stroke of the jack indicated on the label should never be exceeded.
1.3 The jack should be supported on a solid, level and horizontal surface which is well illuminated and free of obstructions. Never stand the jack
on asurface which may sink.
1.4 Ensure that there are no persons inside the vehicle to be lifted. Switch off the engine and apply the brake. Ensure the vehicle or element to
be lifted against any type of sliding. Use chocks if appropriate (1). Do not enter the vehicle or start the engine whilst it is supported on the jack or
appropriate stands. The jack is a lifting device only and should never be used to move the vehicle.
1.5 Position the jack under the manufacturer’s recommended lifting point for the vehicle and ensure that it is not corroded, dirty or greasy. This
point should remain centred over the jack saddle. All off-centred loads can slip and accidents may result.
1.6 During raising and lowering of the load, all precautions should be taken to avoid movement of the vehicle load. Traffic may cause the raised
vehicle to rock during roadside use of the jack.
1.7 The jack should be positioned so as to avoid the need for the user to introduce any part of his/her body underneath the vehicle. Never work
under a raised vehicle without previously supporting it with mechanical stands (3) or other appropriate methods. Never position any part of your
body near the movable elements of the jack.
1.8 It is necessary for the operator to be able to observe the lifting device and the load during all movements. In the presence of dangerous
conditions, such as movement of the vehicle, etc, the lifting process must be interrupted.
1.9 Ensure that there are no persons or obstructions underneath the vehicle prior to lowering.
1.10 As an additional safety measure against overload, the jack is fitted with an overload valve set at the factory and which should not be adjus
ted under any circumstances.If nominal capacity of the jack is exceeded the overload valve will stop the lifting operation.
2. USE AND OPERATION
2.1 The
SRWH 21 TOP
jack models have a mechanical safety device (E),which acts automatically when reaching lifting height of 320mm.
To unlock the mechanical safety device lift the jack lightly and open the Release valve as per point 2.7.
2.2. Prior to operating the jack, remove any accumulated air from the system as follows:
-Insert the handle into the socket and fix it with the screw provided .
-Pull the handle and turn it clockwise and, whilst held in this position , pump the jack several times
to ensure internal lubrication and bleed the accumulated air from the system.
2.3. Release the handle and it will automatically return back to the initial position (“Dead man principle”).
The jack is now ready to be used.
Important: Prior to lifting the load, ensure that all of the aforementioned safety instructions are followed.
2.4. The wheel of the jacks should always rotate freely .
2.5. These jacks are fitted with a foot pedal that gives a faster approach to the load .
2.6. For lifting, move the handle up and down using the full stroke range of the piston for greater speed (2). Secure
the lifted load as an essential safety measure with an appropriate axle stand (3).
2.7. Before lowering, lift the vehicle to remove the axle stands, ensuring that there are no persons or obstacles under the vehicle to be lowered.
Pull the handle and turn it clockwise (4).
2.8. Our jacks are fitted with a safety device LCS that functions automatically and offers smooth and uniform lowering.
2.9. Once the vehicle has been lowered release the handle and it will automatically return back to the initial position.
3 MAINTENANCE
Important: Both the maintenance and repair of the jack may only be performed by qualified persons, who have sufficient knowledge of the
hydraulic systems used in these devices as a result of their training and experience.
3.1 Keep the jack clean and lubricate all moving parts at regular intervals (5), which must be clean and protected from aggressive conditions at all times.
3.2 Only original spare parts should be used.
3.3 Prior to each use, check for bent, broken, cracked or loose parts and solve the problem, if appropriate. If it is suspected that the jack has
been subjected to abnormal loads or has suffered any knocks, withdraw it from service until the problem has been rectified.
3.4 If the oil level needs to be checked or refilled, with the piston fully retracted, remove the filler plug and drain its contents into a container.
With the jack in a horizontal position, proceed to introduce the necessary volume as indicated for each model in these instructions.
The parts table alongside shows the volume of oil required.
Make sure that no dirt enters with the new oil.
Following a period of prolonged intensive use, it is recommendable to change the oil in order to extend the useful life of the jack.
Important: An excess of oil to the volume required may render the jack inoperative.
3.5 Only use hydraulic oil, type HL or HM, with an ISO maximun grade of cinematic viscosity of 30 cST at 40º, or an Engler viscosity of 3 at 50ºC.
Extremely Important: Never use brake fluid.
3.6 When the jack is not in use, make sure the lifting arm is fully retracted to avoid corrosion.
Apply an anti-corrosion product to the pistons, if appropriate.
3.7 Keep the jack in a clean, dry place and out of children reach.
3.8 At the end of the useful life of the jack, drain off the oil and hand it over to an authorised agent and dispose of the jack in accordance with
local regulations.
3.9 Both the repair kit, which exclusively contains the o-rings and seals of the jack , and the spare part sets must be ordered using the reference
assigned in the table.