background image

35

Installation instructions

Assembly sequence (Ref. fig. 36)

The 

TRISTAR 3900 2S ÷ TRISTAR 6100 2S

 boilers are supplied 

with casing, for the mounting of the panel board, do the following:

A) Dismount the right upper walkways (pos. 1 and 2).
B) Fix the support box of the panel board to the bracket on the 

right side of the boiler.

C) Remove the lower cover pos. 4 from the support box of the 

panel board.

  Fasten the panel board (pos. 5) to the support box pos. 3.
D) Rotate the cover of the panel board frontwards after having 

removed the two screws on the side and insert the electric 
inlet cables and the outlet probe capillaries through the slots 
at the base.

fig. 36

TRISTAR 3900÷6100 2S

A

3

4

1

2

5

  Insert the thermostat probe capillaries in the tube designed 

for their passage, that is placed under the casing (see detail 
“A”). 

  Pay special attention when unrolling the capillaries and insert 

the bulbs in the two holders, inserting the contact springs and 

blocking the capillaries with the fixing springs.

E) After having carried out the electric connections, close the 

panel board and reposition the lower cover of the support box.

F) Remount the upper walkways. 

Summary of Contents for Tristar 2S





















































Reviews: