UNI-T UTS3000B/A Series User Manual Download Page 75

Page: 75 / 78

x dB

-100dB

-0.1dB

Noise BW

(ACP)

100Hz

8.41GHz

Integral BW

(ACP)

100Hz

8.41GHz

Offset Freq

(ACP)

0Hz

4.204999950GHz

Carrier BW

(CNR)

100Hz

8.409999800GHz

Noise BW

(CNR)

100Hz

4.404999950GHz

Offset Freq

(CNR)

100Hz

4.404999950GHz

Fundamental

100Hz

4.200000000GHz

Harmonics

Troubleshooting

This chapter lists the possible faults and troubleshooting methods of the spectrum analyzer.

Please follow the corresponding steps to handle it, if these methods is not work, please contact UNI-T

and provide your machine.

Device information (acquisition method:

[System] >Information

)

1. After press the power soft switch, the spectrum analyzer still display a blank screen, and nothing is

displayed.

Check whether the power connector is properly connected and the power switch is turned on.

Check whether the power supply meets the requirements.

Check whether the fuse of the machine is installed or blown.

2. Press the power switch, if the spectrum analyzer still display blank screen and nothing is displayed.

Check the fan. If the fan rotates but the screen is off, the cable to the screen may be loose.

Check the fan. If the fan does not rotate and the screen is off, it presents the instrument is not

enabled.

In case of the above faults, do not disassemble the instrument by yourself. Please contact UNI-T

immediately.

3. Spectral line is not updated for a long time.

Check whether the current trace is in update state or multiple averaging state.

Check whether the current is meet the restriction conditions. Check the restriction settings and

whether there are restriction signals.

In case of the above faults, do not disassemble the instrument by yourself. Please contact UNI-T

Summary of Contents for UTS3000B/A Series















































































Search results

Summary of Contents for UTS3000B/A Series

Reviews:

Related manuals for UTS3000B/A Series

Brands by name

Popular brands

UNI-T UTS3000B/A Series, User Manual

Search results

Summary of Contents for UTS3000B/A Series

Reviews:

Related manuals for UTS3000B/A Series

Brands by name

Popular brands