background image

Dear Users:

Hello! Thank you for choosing this brand new UNI-T device. In order to safely and correctly use this instrument, please read this manual
thoroughly before use, especially the Safety Information part.

After reading this manual, it is recommended to keep the manual at an easily accessible place, preferably close to the device, for future
reference.

Introduction

UNI-TREND TECHNOLOGY (CHINA) CO., LTD., all rights reserved.

UNI-T products are protected by patent rights in China and foreign countries, including issued and pending patents.

UNI-T reserves the rights to any product specification and pricing changes.

UNI-T reserves all rights. Licensed software products are properties of UNI-T and its subsidiaries or suppliers, which are protected by

national copyright laws and international treaty provisions. Information is this manual supersedes all previously published versions.

UNI-T is the registered trademark of UNI-TREND TECHNOLOGY (CHINA) CO., LTD.

If the original purchaser sells or transfers the product to a third party within three years from the date of purchase of the product, the

warranty period of three years shall be from the date of the original purchase from UNI-T or an authorized UNI-T distributor. Accessories

and fuses, etc. are not included in this warranty.

If the product is proved to be defective within the warranty period, UNI-T reserves the rights to either repair the defective product without

charging of parts and labor, or exchange the defected product to a working equivalent product (determined by UNI-T). Replacement

parts, modules and products may be brand new, or perform at the same specifications as brand new products. All original parts, modules,

or products which were defective become the property of UNI-T.

Copyright Information

Summary of Contents for UTG9000C-II Series






























Reviews: