UNI-T UPO1000X Series Service Manual Download Page 26

Page: 26 / 31

Service Manual

UPO1000X Series

Instruments.uni-trend.com

26 / 31

Press power key

Wheter

fan is

turning?

Whether

power key

is turns

red?

Whether

power key

is turns

red?

1. Check fan’s connecting wire
2. Check fan’s power supply
3. Check whether fan is broken

Confirm
1. Wheter power cable is connected

to the oscilloscope?

2. Wheter power cable is connected

to the AC power socket?

3. Wheter the AC power socket

have AC power?

4. Replace power cable

Whether

power key

is turns

red?

Connecting power

supply

Open power siwtch

Whether

power key

is turns

green?

1. Check keyboard’s connection

wire.

2. Check whether MOS Q4 in

keyboard is working properly?

3. Check whether MCU is

working properly?

Yes

Start

Yes

Summary of Contents for UPO1000X Series
































Search results

Summary of Contents for UPO1000X Series

Reviews:

Related manuals for UPO1000X Series

Brands by name

Popular brands

UNI-T UPO1000X Series, Service Manual

Search results

Summary of Contents for UPO1000X Series

Reviews:

Related manuals for UPO1000X Series

Brands by name

Popular brands