background image

Documents are only to be used and distributed completely and unchanged. It is strictly the users’ responsibility to check carefully 

the validity of this document with respect to his product.

page 4 of 24

No. 47800-2-02-5

•  Comply with 

maximum permissible pressures

 at inlet and outlet and pressure 

differences, see section ”Technical data”. Do not operate the pump with overpres-

sure at the inlet.

•  Check  that  mains  voltage  and  current  conform  with  the  equipment  (see  rating 

plate).

•  Change the setting of the voltage changeover switch (pump with dual-voltage 

motor) only if the pump is separated from mains. Check that the voltage changeo-

ver switch is set correctly. 

Attention

: If the pump is switched on with wrong volt-

age selection, the motor might be damaged!

•  Avoid overpressure of more than 0.2 bar in case inert gas is connected to the 

pump, the gas ballast or to a venting valve.

•  Connect pipes gas tight at inlet and outlet of the pump.

• 

Attention:

 Flexible elements tend to shrink when evacuated.

Provide  a  firm  level  platform  for  the  equipment  and  check  that  the  system  to  be 

evacuated is mechanically stable and that all fittings are secure. Ensure a stable po

-

sition of the pump without any mechanical contact except of the pump feet. Comply 

with all applicable safety regulations.

Keep a distance of minimum 20 cm between fan and ambient parts (e.g. housing, 

walls, ...). Check fan regularly for dust/dirt, clean if necessary to avoid a cutback of 

ventilation.

If the equipment is brought from cold environment into a room for operation, allow 

the equipment to warm up (pay attention to water condensation on cold surfaces).

The diameter of the inlet and outlet pipeline should be at least as large as the diam-

eter of the pump connection pipelines.

Comply with all 

applicable and relevant safety requirements

 (regulations and 

guidelines), 

implement the required actions and adopt suitable safety meas-

ures

.

Ambient conditions

To the best of our knowledge the equipment is in compliance with the requirements 

of the applicable EC-directives and harmonized standards (see ”Declaration of con-

formity”) with regard to design, type and model. Directive IEC 1010 gives in detail 

conditions under which the equipment can be operated safely (see also IP degree 

of protection).

Adopt suitable measures in case of differences, e. g. using the equipment outdoors, 

installation in altitudes of more than 1000 m above mean sea level, conductive pol-

lution or bedewing.

Pay attention to the 

permissible maximum ambient and gas inlet temperatures 

(see ”Technical data”).

NOTICE

NOTICE

Summary of Contents for MD 4U NT

























Reviews: