ULTRASUN Q6-0 Manual Download Page 16

 

 

16

 

 

Recommended exposure times for the Q6 – for UV4: 

 

 

RECOMMENDED EXPOSURE SCHEDULE 

MAXIMUM EXPOSURE TIMES (IN 

MINUTES) 

CLASS 

SKIN TYPES 

week 1  week 2  week 3  week 4 

Sensitive skin 

Tanning not advised 

Burns easily and severly, and does not 

tan. 

II 

Light skin 

10 

15 

20 

Burns easily and severly, and tans 

minimally.  

III 

Normal skin 

12 

16 

20 

Burns moderately, and tans 

moderately 

IV 

Dark skin 

13 

17 

20 

Burns minimally, and tans well or 

above agerage.  

 

Allow at least 48 hours between all exposures, tan maintenance: 1-2 times weekly 

MAXIMUM EXPOSURE TIME: 20 minutes. 

 

 

 

Notice the following tanning rules for proper and safe use of your tanning device :

 

 

 

The exposure time for first session must not be shorter than 1 minute. 

 

Follow the recommendations concerning exposure duration and exposure intervals 

 

Protect your eyes from visible and infrared radiation, take adequate precautions  ! Always use 

the provided sunglasses! 

 

Do not sunbath and use the machine on the same day. 

 

This device is intended to be used by one person at a time! 

 

Lie on the sunlamp bed and lower the top section to its internally regulated stop point to attain 

this position. Any other position may result in overexposure. 

 

Always use the protective sunglasses provided. 

 

Remove cosmetics well in advance of exposure and do not apply any sunscreens. 

 

Do not undergo exposure when taking medicines or using cosmetics, which increase sensitivity to 

ultraviolet radiation. If in doubt, take medical advice. 

 

Follow the recommendations concerning exposure duration and exposure intervals. 

 

Seek medical advice if persistent lumps, sores or pigmented moles develop on the skin. 

 

Ultraviolet radiation from the sun or UV-machines can cause injury to skin or eyes. These 

biological effects depend upon the quality and the quantity of the radiation as well as the skin 

sensitivity of the individual. 

 

The skin may develop sunburn after an excessive exposure. Excessively repeated exposure to 

ultraviolet radiation from the sun or the machine may lead to premature ageing of the skin as 

well as increased risk of development of skin tumours. 

 

 

 

 

 

 

 

 

 

 

 

  

  

  

 

 

 

      

Exposure Schedule Q6 

Summary of Contents for Q6-0

























Reviews: