manualshive.com logo in svg

ultraPLAY Discovery Center DC-1SM, Assembly Instructions Manual

Share
Download
ultraPLAY Discovery Center DC-1SM Assembly Instructions Manual Download Page 49

47

         

UltraPlay Play Systems

         800.458.5872  •  www.ultraplay.com

         

UltraPlay Play Systems

         800.458.5872  •  www.ultraplay.com

TouchMath

Panel

1. With TouchMath Panel in position,

    place Gear Panel(A) onto Lower Post #3.

    Insert “wings” of Gear Panel(A) between

    “wings” of TouchMath Panel. 

2. Align Holes in “wings” of TouchMath Panel and

    Gear Panel(A) and insert Upper Post #2(B) downward

    through both sets of “wings” and through deck.

3. Hand tighten Upper Post #2(B) clockwise until tight.

           

     NOTE: Upright Posts(B) are numbered 1,2,3 & 4. 

                Match Upright Posts to Footer Posts.

  

A

B

2

2

3

ROOF OPTION INSTRUCTIONS

STEP 6 - INSTALL GEAR PANEL

Parts List

Letter

Description

Quantity Part Number

A

Gear Panel

1

02-08-0046

B

Upper Post - 57.48” Long

1

02-08-0117

Summary of Contents for Discovery Center DC-1SM



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands